Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255543 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69350 1.INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

B183291E06
0.875,1.271 0.875,0.854 0.875,0.854 0.667,0.854 false 0.667,1.344 0.667,1.677 0.667,1.677 0.823,1.677 false 0.521,1.313 0.333,1.313 0.333,1.313 0.333,1.531 false 0.865,1.615 1.479,1.896 0.615,0.281 10 false ACT+ 0.281,0.792 0.896,1.073 0.615,0.281 10 false ACT- 3.531,0.448 3.844,0.688 0.313,0.24 10 false *1 6,0.448 6.333,0.656 0.333,0.208 10 false *2 0.271,0.115 0.583,0.354 0.313,0.24 10 false *a 0.292,1.531 0.542,1.698 0.25,0.167 10 false +

Text in Illustration
*1 Full-latch *2 Open-latch
*a Component without harness connected
(Back Door Lock assembly)
- -

a.

Set the back door lock to the full-latch position.


b.

Apply battery voltage to the door motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (ACT+)
Battery negative (-) → 1 (ACT-)
Moves to open-latch position


If the result is not as specified, replace the back door lock assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ACT-) - 3 (+) Open-latch Below 1 Ω
1 (ACT-) - 3 (+) Full-latch 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly.



Hide 69350 2.INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)

a.
B300755E02
2.813,1.573 3.177,2.229 true 2.625,1.583 2.26,2.24 true 1.427,2.521 1.333,2.521 1.333,2.521 0.865,1.708 true 0.104,0.073 0.365,0.313 0.26,0.24 10 false *a 1.573,2.823 1.792,2.979 0.219,0.156 10 false *4 1.615,3 1.823,3.229 0.208,0.229 10 false *5 3.063,2.271 3.313,2.479 0.25,0.208 10 false M+ 2.156,2.271 2.385,2.49 0.229,0.219 10 false M- 1.438,2.438 1.729,2.625 0.292,0.188 10 false *3 0.333,0.979 0.521,1.146 0.188,0.167 10 false *1 1.104,1 1.292,1.146 0.188,0.146 10 false *2 1.458,3.615 1.656,3.813 0.198,0.198 10 false *6 1.219,3.969 1.396,4.167 0.177,0.198 10 false *7

Inspect the closer motor operation.

i.

Set the back door lock assembly to the full-latch position.


ii.

Apply battery voltage and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (M+)
Battery negative (-) → 2 (M-)
Moves to open-latch position


If the result is not as specified, replace the back door lock assembly.



iii.

Set the back door lock assembly to the half-latch position.


iv.

Apply battery voltage and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (M-)
Battery negative (-) → 1 (M+)
Moves to over-latch position


If the result is not as specified, replace the back door lock assembly.

Text in Illustration
*1 Release
*2 Close
*3 Drive Gear
*4 Over-latch
*5 Full-latch
*6 Half-latch
*7 Open-latch
*a Component without harness connected
(Back Door Lock Assembly)




b.
B300756E02
2.521,1.229 2.125,1.604 true 2.125,1.823 2.51,1.354 true 2.698,1.219 3.167,1.708 true 2.667,1.385 2.677,1.781 true 0.771,1.708 1.208,2.656 1.208,2.656 1.302,2.656 true 2.188,2.49 1.521,2.49 1.521,2.49 1.073,1.948 true 1.677,2.229 1.542,2.229 1.542,2.229 1.094,1.729 true 1.719,2.938 1.917,3.135 0.198,0.198 10 false *6 1.75,3.198 1.927,3.396 0.177,0.198 10 false *7 1.563,3.833 1.76,4.052 0.198,0.219 10 false *8 1.271,4.354 1.49,4.552 0.219,0.198 10 false *9 0.135,0.063 0.406,0.281 0.271,0.219 10 false *a 2.531,1.823 2.833,1.969 0.302,0.146 10 false CLS 1.865,1.823 2.292,1.969 0.427,0.146 10 false OPN 1.99,1.573 2.115,1.719 0.125,0.146 10 false E 3.021,1.729 3.344,1.875 0.323,0.146 10 false CTY 0.438,1.052 0.656,1.25 0.219,0.198 10 false *1 1.125,1.042 1.344,1.24 0.219,0.198 10 false *2 1.313,2.563 1.583,2.771 0.271,0.208 10 false *5 2.229,2.385 2.417,2.563 0.188,0.177 10 false *4 1.677,2.146 1.885,2.323 0.208,0.177 10 false *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Half-latch Switch
Tester Connection Condition Specified Condition
5 (CLS) - 4 (E) Over-latch Below 1 Ω
Full-latch 10 kΩ or higher
Half-latch 10 kΩ or higher
Open-latch Below 1 Ω


If the result is not as specified, replace the back door lock assembly.

Closer Position Switch:
Tester Connection Condition Specified Condition
6 (OPN) - 4 (E) Selector gear is in center position Below 1 Ω
Selector gear is not in center position 10 kΩ or higher



If the result is not as specified, replace the back door lock assembly.


Back Door Courtesy Switch:
Tester Connection Condition Specified Condition
3 (CTY) - 4 (E) Half-latch
Open-latch
Below 1 Ω
Over-latch
Full-latch
10 kΩ or higher


If the result is not as specified, replace the back door lock assembly.

Text in Illustration
*1 Release
*2 Close
*3 Closer Position Switch
*4 Selector Gear
*5 Drive Gear
*6 Over-latch
*7 Full-latch
*8 Half-latch
*9 Open-latch
*a Component without harness connected
(Back Door Lock Assembly)