Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK › from 2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255543 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69350 1.INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

a.
B421507E03
1.49,4.021 1.167,4.344 false 2,4.021 2.302,4.323 false 1.74,4.031 1.74,4.323 false 2.021,1.208 2.385,1.365 false 2.052,2.927 2.406,3.083 false 1.031,4.313 1.688,4.563 0.656,0.25 10 false + 1.625,4.354 2.073,4.573 0.448,0.219 10 false ACT- 2.354,4.292 2.854,4.531 0.5,0.24 10 false ACT+ 0.448,1.74 0.604,1.917 0.156,0.177 10 false *a 0.75,3.354 0.906,3.531 0.156,0.177 10 false *c 0.438,0.083 0.594,0.26 0.156,0.177 10 false *b 2.427,3.031 2.583,3.208 0.156,0.177 10 false *1 2.417,1.292 2.573,1.469 0.156,0.177 10 false *1

Check the operation of the door lock motor.

Text in Illustration
*1 Latch
*a Open
*b Close
*c Component without harness connected
(Back Door Lock Assembly)

i.

Move the back door lock assembly to the close position.


ii.

Apply battery voltage to the door lock motor assembly and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (ACT+)
Battery negative (-) → 2 (ACT-)
Close → Open


If the result is not as specified, replace the back door lock assembly.



Hide 69350 2.INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)

a.
B421500E02
1.564,2.927 1.883,2.927 false 0.978,2.926 1.297,2.926 false 1.919,2.841 2.098,3.023 0.179,0.181 10 M- 0.707,2.837 0.921,3.018 0.214,0.181 10 M+ 0.687,2.397 0.843,2.579 0.156,0.181 10 *a 0.802,2.016 0.958,2.198 0.156,0.181 10 *c 1.787,2.034 1.943,2.215 0.156,0.181 10 *b 0.86,0.915 1.144,1.161 0.284,0.246 0.962,0.934 1.118,1.115 0.156,0.181 10 *b 1.578,0.911 1.734,1.092 0.156,0.181 10 *c

Check the operation.

Text in Illustration
*a Component without harness connected
(Back Door Lock Assembly)
*b Close Operation Direction
*c Open Operation Direction

i.

Apply battery voltage and check the operation of the closer motor.

OK:
Battery Connection Result
Battery positive (+) → 1 (M-)
Battery negative (-) → 2 (M+)
Close Operation
Battery positive (+) → 2 (M+)
Battery negative (-) → 1(M-)
Open Operation


If the result is not as specified, replace the back door lock assembly.



b.
B421501E01
0.06,1.446 0.216,1.628 0.156,0.181 10 *b 0.52,0.26 0.675,0.442 0.156,0.181 10 *c 1.461,0 1.617,0.181 0.156,0.181 10 *d 2.157,0.028 2.313,0.210 0.156,0.181 10 *e 1.535,2.844 1.131,2.844 false 2.265,2.844 1.861,2.844 false 0.74,2.761 1.027,2.942 0.287,0.181 10 CLS 2.275,2.765 2.431,2.947 0.156,0.181 10 E 0.92,2.349 1.076,2.530 0.156,0.181 10 *a

Check the resistance of the half latch switch.

Text in Illustration
*a Component without harness connected
(Back Door Lock Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Over Stroke Position

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CLS) - 1 (E) Open position Below 1 Ω
3 (CLS) - 1 (E) Open position → Half-latch position Below 1 Ω → 10 kΩ to higher
3 (CLS) - 1 (E) Half-latch position 10 kΩ to higher
3 (CLS) - 1 (E) Full-latch position 10 kΩ to higher
3 (CLS) - 1 (E) Over Stroke Position 10 kΩ to higher


If the result is not as specified, replace the back door lock assembly.



c.
B421501E02
1.838,2.848 2.225,2.848 false 1.835,2.995 2.179,3.186 false 2.242,2.767 2.398,2.948 0.156,0.181 10 E 2.239,3.108 2.534,3.289 0.295,0.181 10 CTY 0.079,1.475 0.266,1.656 0.187,0.181 10 *b 1.025,2.326 1.212,2.507 0.187,0.181 10 *a 0.431,0.328 0.587,0.509 0.156,0.181 10 *c 1.501,0 1.657,0.181 0.156,0.181 10 *d 2.163,0.074 2.319,0.255 0.156,0.181 10 *e

Check the resistance of the full latch switch.

Text in Illustration
*a Component without harness connected
(Back Door Lock Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Over Stroke Position

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (CTY) - 1 (E) Open position Below 1 Ω
4 (CTY) - 1 (E) Half-latch position Below 1 Ω
4 (CTY) - 1 (E) Half-latch position → Full-latch position Below 1 Ω → 10 kΩ to higher
4 (CTY) - 1 (E) Full-latch position 10 kΩ to higher
4 (CTY) - 1 (E) Over Stroke Position 10 kΩ to higher


If the result is not as specified, replace the back door lock assembly.



d.
B421501E08
1.844,2.896 2.104,2.896 true 1.688,2.833 1.958,2.563 1.958,2.563 2.115,2.563 false 2.135,2.823 2.292,3 0.156,0.177 10 false E 2.167,2.49 2.552,2.667 0.385,0.177 10 false POLE 0.958,2.375 1.115,2.552 0.156,0.177 10 false *a 0.052,1.563 0.208,1.74 0.156,0.177 10 false *b 0.479,0.375 0.635,0.552 0.156,0.177 10 false *c 1.458,0.052 1.615,0.229 0.156,0.177 10 false *d 2.167,0.24 2.323,0.417 0.156,0.177 10 false *e

Check the resistance of the pawl switch.

Text in Illustration
*a Component without harness connected
(Back Door Lock Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Over Stroke Position

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (POLE) - 1 (E) Open position Below 1 Ω
2 (POLE) - 1 (E) Open position → Half-latch position 10 kΩ to higher → Below 1 Ω → 10 kΩ to higher
2 (POLE) - 1 (E) Half-latch position 10 kΩ to higher
2 (POLE) - 1 (E) Half-latch position → Full-latch position 10 kΩ to higher → Below 1 Ω → 10 kΩ to higher
2 (POLE) - 1 (E) Full-latch position 10 kΩ to higher
2 (POLE) - 1 (E) Over Stroke Position 10 kΩ to higher


If the result is not as specified, replace the back door lock assembly.



e.
B421499E01
1.449,2.947 1.083,2.947 false 2.128,2.836 1.762,2.836 false 2.133,2.761 2.289,2.942 0.156,0.181 10 E 0.662,2.856 0.980,3.037 0.318,0.181 10 OPN 0.898,2.387 1.054,2.569 0.156,0.181 10 *a 1.487,0.015 1.643,0.197 0.156,0.181 10 *b

Check the resistance of the sector switch.

Text in Illustration
*a Component without harness connected
(Back Door Lock Assembly)
*b Sector Gear in Neutral Position

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (OPN) - 1 (E) Sector gear in neutral position (Sector switch on) Below 1 Ω
6 (OPN) - 1 (E) Sector gear in neutral position (Sector switch off) 10 kΩ to higher


If the result is not as specified, replace the back door lock assembly.