Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255549 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch  


DESCRIPTION

The main body ECU receives switch signals from the door control switch and activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B194715E06
5.688,1.49 5.844,1.667 0.156,0.177 10 false 4 5.688,0.729 5.865,0.906 0.177,0.177 10 false 2 5.688,2.104 5.844,2.281 0.156,0.177 10 false 3 5.885,2.094 6.042,2.271 0.156,0.177 10 false E 5.885,1.49 6.083,1.667 0.198,0.177 10 false L 5.885,0.729 6.125,0.906 0.24,0.177 10 false UL 5.844,3.74 6.823,3.917 0.979,0.177 10 false I33 4.375,1.479 4.531,1.656 0.156,0.177 10 false 9 4.771,1.417 5.01,1.573 0.24,0.156 10 false 49 4.052,1.635 4.292,1.823 0.24,0.188 10 false L1 4.021,0.844 4.302,1.042 0.281,0.198 10 false UL1 4.771,0.667 4.99,0.875 0.219,0.208 10 false 52 4.344,0.708 4.51,0.885 0.167,0.177 10 false 12 4.771,1.625 5.01,1.833 0.24,0.208 10 false 2D 4.76,0.844 5,1.052 0.24,0.208 10 false 2D 5.802,3.927 7.125,4.333 1.323,0.406 10 false Door Control Switch (for Passenger Side) 3.115,4.281 4.177,4.51 1.063,0.229 10 false Main Body ECU 2.219,2.26 3.052,2.438 0.833,0.177 10 false DOOR NO. 1 0.99,3.052 1.823,3.229 0.833,0.177 10 false DOOR NO. 2 3.156,2.854 3.531,3.031 0.375,0.177 10 false BATB 3.156,2.125 3.521,2.302 0.365,0.177 10 false ALTB 3.156,3.427 3.604,3.667 0.448,0.24 10 false GND2 1.854,3.427 2.094,3.635 0.24,0.208 10 false 2D 1.854,2.854 2.094,3.063 0.24,0.208 10 false 2B 1.854,2.125 2.094,2.333 0.24,0.208 10 false 2A 1.875,3.188 2.073,3.365 0.198,0.177 10 false 62 1.875,2.646 2.083,2.823 0.208,0.177 10 false 20 1.896,1.917 2.021,2.083 0.125,0.167 10 false 1 0.281,2.125 0.75,2.563 0.469,0.438 10 false from Battery 0.281,2.854 0.75,3.292 0.469,0.438 10 false from Battery 2.938,3.292 3.073,3.448 0.135,0.156 10 false 4 2.938,2.708 3.052,2.917 0.115,0.208 10 false 2 2.948,2.01 3.073,2.208 0.125,0.198 10 false 6 2.625,4.75 4.479,4.979 1.854,0.229 10 false Cowl Side Junction Block LH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK AND UNLOCK SWITCH)
a.

Use the Data List to check if the door lock and unlock switches are functioning properly.

Main Body ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door manual lock switch signal / ON or OFF ON: Front passenger side door control switch on (lock)
OFF: Front passenger side door control switch off
-
Door Unlock SW-Unlock Door manual unlock switch signal / ON or OFF ON: Front passenger side door control switch on (unlock)
OFF: Front passenger side door control switch off
-

OK:

On the intelligent tester screen, each item changes between ON and OFF according to above chart.




OK

2.INSPECT FUSE (DOOR NO. 1, DOOR NO. 2)

NG

4.INSPECT DOOR CONTROL SWITCH ASSEMBLY (DOOR LOCK AND UNLOCK SWITCH)
2.INSPECT FUSE (DOOR NO. 1, DOOR NO. 2)
a.

Remove the DOOR NO. 1 fuse from the main body ECU (cowl side junction block LH).


b.

Remove the DOOR NO. 2 fuse from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DOOR NO. 1 fuse Always Below 1 Ω
DOOR NO. 2 fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
U164137E01
0.036,0.035 2.393,0.372 2.357,0.336 10 Front view of wire harness connector: (to Main Body ECU) 0.133,1.112 0.334,1.268 0.201,0.156 10 2A 1.785,1.106 1.986,1.262 0.201,0.156 10 2B 1.33,1.455 1.712,1.601 0.382,0.145 10 ALTB 3.144,1.609 3.526,1.754 0.382,0.145 10 BATB 0.954,1.396 1.31,1.507 false 3.166,1.382 3.278,1.593 false 4.352,1.102 4.553,1.258 0.201,0.156 10 2D 5.797,1.602 6.227,1.747 0.430,0.145 10 GND2 6.248,1.369 6.021,1.594 false

a.

Disconnect the 2A, 2B, and 2D ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2A-1 (ALTB) - Body ground Always 11 to 14 V
2B-20 (BATB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-62 (GND2) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DOOR CONTROL SWITCH ASSEMBLY (DOOR LOCK AND UNLOCK SWITCH)
B180461E07
1.781,0.667 2.5,0.667 false 1.49,0.667 0.979,0.667 false 1.75,3.625 2.021,4.177 false 1.615,3.635 1.615,4.146 false 1.469,3.646 1.271,4.167 false 2.542,0.594 2.917,0.792 0.375,0.198 10 false Lock 0.51,0.583 1.281,0.781 0.771,0.198 10 false Unlock 0.25,2.208 2.76,2.698 2.51,0.49 10 false Component without harness connected: (Door Control Switch) 1.208,4.167 1.385,4.396 0.177,0.229 10 false L 1.958,4.167 2.156,4.344 0.198,0.177 10 false UL 1.563,4.177 1.719,4.354 0.156,0.177 10 false E

a.

Remove the door control switch (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (UL) - 3 (E) Unlock Below 1 Ω
2 (UL) - 3 (E)
4 (L) - 3 (E)
Off 10 kΩ or higher
4 (L) - 3 (E) Lock Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH AND BODY GROUND)

NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH AND BODY GROUND)
U164293E02
1.563,1.958 1.802,2.396 false 1.302,1.958 1.063,2.396 false 5.802,2.031 6.052,2.438 false 5.323,2.031 5.073,2.438 false 5.563,2.042 5.563,2.448 false 0.615,0.313 2.99,0.75 2.375,0.438 10 false Front view of wire harness connector: (to Main Body ECU) 4.49,0.313 6.865,0.75 2.375,0.438 10 false Front view of wire harness connector: (to Door Control Switch) 0.385,1.635 0.635,1.802 0.25,0.167 10 false 2D 4.396,1.635 4.646,1.802 0.25,0.167 10 false I33 0.969,2.396 1.25,2.563 0.281,0.167 10 false L1 1.677,2.396 2.052,2.583 0.375,0.188 10 false UL1 6.125,2.458 6.24,2.594 0.115,0.135 10 false L 5.531,2.49 5.646,2.625 0.115,0.135 10 false E 4.948,2.469 5.188,2.646 0.24,0.177 10 false UL

a.

Disconnect the 2D ECU connector.


b.

Disconnect the I33 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-52 (UL1) - I33-2 (UL) Always Below 1 Ω
2D-49 (L1) - I33-4 (L) Always Below 1 Ω
I33-3 (E) - Body ground Always Below 1 Ω
I33-2 (UL) - Body ground Always 10 kΩ or higher
I33-4 (L) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR