Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255549 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder  


DESCRIPTION

The main body ECU receives switch signals from the multiplex network master switch, and driver side door key cylinder switch signals from the front door lock. The main body ECU activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

U164202E02
5.198,2.104 4.635,2.104 4.635,2.104 4.635,2.354 false 4.667,2.417 4.604,2.417 false 4.688,2.385 4.594,2.385 false 4.698,2.354 4.573,2.354 false 4.698,4.635 4.896,4.792 0.198,0.156 10 false 53 3.854,4.813 4.094,5 0.24,0.188 10 false L2 3.771,4.031 4.052,4.177 0.281,0.146 10 false UL3 3.854,1.521 4.094,1.708 0.24,0.188 10 false L1 3.771,0.948 4.052,1.094 0.281,0.146 10 false UL1 2.875,3.208 3.594,3.354 0.719,0.146 10 false ALTB 2.875,3.927 3.51,4.073 0.635,0.146 10 false BATB 2.896,5.344 3.938,5.5 1.042,0.156 10 false Main Body ECU 2.344,5.781 4.26,5.938 1.917,0.156 10 false Cowl Side Junction Block LH 1,6.594 2.604,6.75 1.604,0.156 10 false LIN Communication Line 6.104,4.74 6.25,4.885 0.146,0.146 10 false L 5.802,3.146 5.99,3.292 0.188,0.146 10 false 7 6.104,3.938 6.344,4.083 0.24,0.146 10 false UL 6.104,1.531 6.25,1.677 0.146,0.146 10 false L 6.104,0.938 6.344,1.083 0.24,0.146 10 false UL 5.802,3.823 5.99,3.969 0.188,0.146 10 false 10 4.208,3.823 4.396,3.969 0.188,0.146 10 false 10 2.688,3.115 2.802,3.26 0.115,0.146 10 false 6 2.667,3.833 2.781,3.979 0.115,0.146 10 false 2 2.667,4.406 2.781,4.552 0.115,0.146 10 false 4 4.104,4.75 4.292,4.896 0.188,0.146 10 false 10 6.104,3.25 6.344,3.396 0.24,0.146 10 false E 5.823,4.635 5.969,4.781 0.146,0.146 10 false 9 5.76,4.813 6.031,4.958 0.271,0.146 10 false I14 5.76,4.021 6.031,4.167 0.271,0.146 10 false I14 5.76,3.333 6.031,3.479 0.271,0.146 10 false I14 5.771,3.51 5.948,3.656 0.177,0.146 10 false *1 5.771,4.198 5.948,4.344 0.177,0.146 10 false *1 5.396,3.823 5.521,3.969 0.125,0.146 10 false 5 5.365,4.021 5.542,4.167 0.177,0.146 10 false I6 5.344,4.198 5.521,4.344 0.177,0.146 10 false *2 5.396,4.635 5.521,4.781 0.125,0.146 10 false 6 5.365,4.823 5.542,4.969 0.177,0.146 10 false I6 5.344,5 5.521,5.146 0.177,0.146 10 false *2 0.385,6.083 1.563,6.229 1.177,0.146 10 false *1: for LHD 0.385,6.333 1.396,6.479 1.01,0.146 10 false *2: for RHD 1.771,6.083 5.531,6.229 3.76,0.146 10 false *3: for Models with Jam Protection Function on 4 Windows 1.771,6.333 6.344,6.479 4.573,0.146 10 false *4: for Models with Jam Protection Function on Driver Door Window Only 5.396,3.146 5.521,3.292 0.125,0.146 10 false 8 5.365,3.344 5.542,3.49 0.177,0.146 10 false I6 5.344,3.521 5.521,3.667 0.177,0.146 10 false *2 5.771,5 5.948,5.146 0.177,0.146 10 false *1 5.781,0.75 5.969,0.896 0.188,0.146 10 false 9 5.802,1.344 5.948,1.49 0.146,0.146 10 false 2 5.74,1.531 6.01,1.677 0.271,0.146 10 false I31 5.74,0.938 6.01,1.083 0.271,0.146 10 false I31 5.76,1.125 5.938,1.271 0.177,0.146 10 false *1 5.375,0.75 5.5,0.896 0.125,0.146 10 false 8 5.323,0.938 5.552,1.083 0.229,0.146 10 false I26 5.333,1.125 5.51,1.271 0.177,0.146 10 false *2 5.375,1.333 5.5,1.479 0.125,0.146 10 false 2 5.333,1.531 5.563,1.677 0.229,0.146 10 false I26 5.333,1.708 5.51,1.854 0.177,0.146 10 false *2 5.76,1.698 5.938,1.844 0.177,0.146 10 false *1 5.938,5.25 7.135,5.625 1.198,0.375 10 false Front Door Lock (for Driver Side) 6.104,0.385 6.417,0.531 0.313,0.146 10 false LIN1 4.969,2.438 7.083,2.635 2.115,0.198 10 false Multiplex Network Master Switch 3.719,0.385 4.031,0.531 0.313,0.146 10 false LIN2 2.875,4.5 3.594,4.646 0.719,0.146 10 false GND2 4.188,4.031 4.385,4.177 0.198,0.146 10 false E1 4.208,0.177 4.396,0.323 0.188,0.146 10 false 10 4.188,0.385 4.385,0.531 0.198,0.146 10 false E3 4.208,0.75 4.396,0.896 0.188,0.146 10 false 52 4.188,0.948 4.458,1.094 0.271,0.146 10 false 2D 4.208,1.333 4.396,1.479 0.188,0.146 10 false 49 4.188,1.531 4.448,1.677 0.26,0.146 10 false 2D 4.688,4.833 4.896,4.979 0.208,0.146 10 false 2D 1.948,3.344 2.792,3.49 0.844,0.146 10 false DOOR NO. 1 1.604,4.302 1.802,4.458 0.198,0.156 10 false 62 1.594,3.927 1.802,4.073 0.208,0.146 10 false 2B 1.604,3.729 1.802,3.885 0.198,0.156 10 false 20 1.594,4.5 1.802,4.646 0.208,0.146 10 false 2D 1.635,3.01 1.74,3.167 0.104,0.156 10 false 1 1.594,3.208 1.802,3.354 0.208,0.146 10 false 2A 0.677,4.094 1.521,4.24 0.844,0.146 10 false DOOR NO. 2 0.104,3.938 0.604,4.271 0.5,0.333 10 false from Battery 0.146,3.177 0.646,3.51 0.5,0.333 10 false from Battery 5.792,1.854 5.979,2 0.188,0.146 10 false 1 6.094,2.031 6.333,2.177 0.24,0.146 10 false E 5.75,2.031 6.021,2.177 0.271,0.146 10 false I31 5.76,2.219 5.938,2.365 0.177,0.146 10 false *1 5.375,1.854 5.5,2 0.125,0.146 10 false 9 5.323,2.031 5.552,2.177 0.229,0.146 10 false I26 5.333,2.219 5.51,2.365 0.177,0.146 10 false *2 5.771,0.198 5.958,0.344 0.188,0.146 10 false 17 5.75,0.365 6.021,0.51 0.271,0.146 10 false I11 5.76,0.552 5.938,0.698 0.177,0.146 10 false *1 5.344,0.188 5.521,0.333 0.177,0.146 10 false 17 5.323,0.365 5.552,0.51 0.229,0.146 10 false I22 5.333,0.563 5.51,0.708 0.177,0.146 10 false *2 4.771,0.229 4.948,0.375 0.177,0.146 10 false *3 4.771,0.865 4.948,1.01 0.177,0.146 10 false *4 4.771,1.448 4.948,1.594 0.177,0.146 10 false *4 4.771,1.938 4.948,2.083 0.177,0.146 10 false *4 6.417,0.396 6.594,0.542 0.177,0.146 10 false *3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Since the power door lock control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK DOOR LOCK OPERATION
Result
Result Proceed to
All doors cannot be locked through multiplex network master switch and driver side door key cylinder A
All doors cannot be locked through multiplex network master switch (for Models with Jam Protection Function on Driver Door Window Only) B
All doors cannot be locked through multiplex network master switch (for Models with Jam Protection Function on 4 Windows) C
All doors cannot be locked through driver side door key cylinder D


A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - MAIN BODY ECU AND BODY GROUND)

C

4.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (OPERATION)

D

5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY LINKED LOCK AND UNLOCK SWITCH)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Disconnect the 2A, 2B and 2D main body ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Condition Specified Condition
2A-1 (ALTB) - Body ground Always 11 to 14 V
2B-20 (BATB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-62 (GND2) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

for LHD:

i.

Disconnect the I31 master switch connector.


ii.

Disconnect the 2D main body ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I31-9 (UL) - 2D-52 (UL1) Always Below 1 Ω
I31-2 (L) - 2D-49 (L1) Always Below 1 Ω
I31-1 (E) - Body ground Always Below 1 Ω
I31-9 (UL) - Body ground Always 10 kΩ or higher
I31-2 (L) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the I26 master switch connector.


ii.

Disconnect the 2D main body ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I26-8 (UL) - 2D-52 (UL1) Always Below 1 Ω
I26-2 (L) - 2D-49 (L1) Always Below 1 Ω
I26-9 (E) - Body ground Always Below 1 Ω
I26-8 (UL) - Body ground Always 10 kΩ or higher
I26-2 (L) - Body ground Always 10 kΩ or higher





OK

4.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (OPERATION)
a.

Replace the multiplex network master switch with a normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Check that all doors can be locked and unlocked by using the multiplex network master switch.

OK:

All doors can be locked and unlocked with multiplex network master switch.




OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY LINKED LOCK AND UNLOCK SWITCH)
a.

Use the Data List to check if the door key linked lock and unlock switches are functioning properly.

Main Body ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Key Linked Lock SW Door key linked lock switch signal / ON or OFF ON: Driver side door key cylinder turned to lock position
OFF: Driver side door key cylinder not turned
-
Door Key Linked Unlock SW Door key linked unlock switch signal / ON or OFF ON: Driver side door key cylinder turned to unlock position
OFF: Driver side door key cylinder not turned
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

6.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK - MAIN BODY ECU AND BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK - MAIN BODY ECU AND BODY GROUND)
a.

for LHD:

i.

Disconnect the I14 door lock connector.


ii.

Disconnect the E1 and 2D main body ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I14-10 (UL) - E1-10 (UL3) Always Below 1 Ω
I14-9 (L) - 2D-53 (L2) Always Below 1 Ω
I14-7 (E) - Body ground Always Below 1 Ω
I14-10 (UL) - Body ground Always 10 kΩ or higher
I14-9 (L) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the I6 door lock connector.


ii.

Disconnect the E1 and 2D main body ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I6-5 (UL) - E1-10 (UL3) Always Below 1 Ω
I6-6 (L) - 2D-53 (L2) Always Below 1 Ω
I6-8 (E) - Body ground Always Below 1 Ω
I6-5 (UL) - Body ground Always 10 kΩ or higher
I6-6 (L) - Body ground Always 10 kΩ or higher





OK

7.INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR KEY LINKED LOCK AND UNLOCK SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR KEY LINKED LOCK AND UNLOCK SWITCH)
a.

for LHD (w/o Double Locking Function):

U164012E01
2.429,0.678 2.849,0.848 0.420,0.170 10 Lock 2.023,2.019 2.530,2.200 0.507,0.180 10 Unlock 2.68,1.684 2.990,1.839 0.310,0.155 10 OFF 4.155,0.233 6.635,0.610 2.480,0.377 10 Component without harness connected: (Front Door Lock LH) 4.227,1.739 4.459,1.884 0.232,0.145 10 I14 5.315,2.347 5.446,2.528 0.131,0.180 10 E 4.482,2.251 4.723,2.404 0.240,0.153 10 UL 5.043,2.347 5.208,2.489 0.164,0.142 10 L 5.365,2.044 5.365,2.339 false 5.077,2.044 5.077,2.339 false 4.923,2.022 4.651,2.294 false

i.

Remove the front door lock LH (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E) Off 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω
10 (UL) - 7 (E) Off 10 kΩ or higher




b.

for LHD (w/ Double Locking Function):

U163861E01
4.161,0.408 6.741,0.751 2.580,0.343 10 Component without harness connected: (Front Door Lock LH) 4.409,1.849 4.622,1.994 0.213,0.145 10 I14 4.642,2.383 4.875,2.551 0.232,0.168 10 UL 5.133,2.383 5.365,2.551 0.232,0.168 10 L 5.588,2.383 5.820,2.551 0.232,0.168 10 E 5.012,2.04 4.744,2.366 false 5.161,2.362 5.161,2.054 false 5.455,2.04 5.616,2.362 false 3.199,1.307 3.682,1.484 0.482,0.177 10 Unlock 3.385,0.57 3.867,0.747 0.482,0.177 10 Lock

i.

Remove the front door lock LH (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E) Off 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω
10 (UL) - 7 (E) Off 10 kΩ or higher




c.

for RHD (w/o Double Locking Function):

U163859E01
4.045,0.478 6.624,0.821 2.580,0.343 10 Component without harness connected: (Front Door Lock RH) 4.466,1.648 4.623,1.793 0.157,0.145 10 I6 5.815,2.369 6.047,2.537 0.232,0.168 10 UL 5.544,2.369 5.776,2.537 0.232,0.168 10 L 4.93,2.369 5.162,2.537 0.232,0.168 10 E 5.273,2.026 5.005,2.352 false 5.577,2.348 5.577,2.04 false 5.722,2.026 5.883,2.348 false 1.425,0.625 1.907,0.802 0.482,0.177 10 Unlock 1.187,1.417 1.669,1.593 0.482,0.177 10 Lock

i.

Remove the front door lock RH (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (UL) - 8 (E) Unlock Below 1 Ω
5 (UL) - 8 (E) Off 10 kΩ or higher
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E) Off 10 kΩ or higher




d.

for RHD (w/ Double Locking Function):

U163860E01
4.045,0.478 6.624,0.821 2.580,0.343 10 Component without harness connected: (Front Door Lock RH) 4.47,1.648 4.629,1.793 0.159,0.145 10 I6 5.796,2.369 6.028,2.537 0.232,0.168 10 UL 5.54,2.369 5.773,2.537 0.232,0.168 10 L 4.976,2.369 5.209,2.537 0.232,0.168 10 E 5.279,2.026 5.011,2.352 false 5.568,2.348 5.568,2.04 false 5.712,2.026 5.873,2.348 false 1.425,0.625 1.907,0.802 0.482,0.177 10 Unlock 1.187,1.417 1.669,1.593 0.482,0.177 10 Lock

i.

Remove the front door lock LH (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (UL) - 8 (E) Unlock Below 1 Ω
5 (UL) - 8 (E) Off 10 kΩ or higher
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E) Off 10 kΩ or higher





OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY