Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255549 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Collision Door Lock Release Function does not Operate  


DESCRIPTION

When an impact is detected, a relay inside the main body ECU is operated to switch the power source of the door lock with motor assemblies from the vehicle battery to the door control battery.

WIRING DIAGRAM

B409277E05
5.729,1.875 6.167,2.063 0.438,0.188 10 false ACTG 1.771,1.896 2.219,2.083 0.448,0.188 10 false ACTG 1.063,2.354 1.458,2.542 0.396,0.188 10 false E168 1.063,2.542 2.375,2.729 1.313,0.188 10 false Door Control Battery 5.573,2.594 6.635,2.896 1.063,0.302 10 false Main Body ECU 1.979,0.74 2.146,0.927 0.167,0.188 10 false IG 5.323,1.885 5.76,2.073 0.438,0.188 10 false E117 5.417,1.677 5.719,1.865 0.302,0.188 10 false 3 3.146,0.74 3.448,0.927 0.302,0.188 10 false 2J 4.552,0.667 5.656,1.021 1.104,0.354 10 false from IG1 NO.1 Relay 3.458,0.896 4.375,1.083 0.917,0.188 10 false ECU-IG NO.2 3.167,0.51 3.469,0.698 0.302,0.188 10 false 12 2.229,0.625 2.531,0.813 0.302,0.188 10 false 8 2.229,1.792 2.531,1.979 0.302,0.188 10 false 9 3.698,1.344 5.625,1.708 1.927,0.365 10 false Cowl Side Junction Block LH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Check door lock operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

All doors lock and unlock normally.




OK

2.CHECK DOOR CONTROL BATTERY

NG

2.CHECK DOOR CONTROL BATTERY
a.
U164355E02
1.458,1.375 1.271,1.792 1.271,1.792 0.927,1.792 false 0.427,1.021 0.833,1.208 0.406,0.188 10 false E168 0.75,1.729 0.927,1.917 0.177,0.188 10 false IG 0.052,0 0.271,0.188 0.219,0.188 10 false *a

Disconnect the door control battery connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E168-8 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Door Control Battery)



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL BATTERY)

NG

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL BATTERY)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL BATTERY)
a.

Disconnect the 2J main body ECU connector.


b.

Disconnect the E168 door control battery connector.


c.

Measure the resistance according to the value(s) in the table.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-3 (ACTG) - E168-9 (ACTG) Always Below 1 Ω
E117-3 (ACTG) or E168-9 (ACTG) - Body ground Always 10 kΩ or higher




OK

4.REPLACE DOOR CONTROL BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE DOOR CONTROL BATTERY
a.

Replace the door control battery with new or known good one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL BATTERY(for LHD)>REMOVAL).



NEXT

5.CHECK DOOR CONTROL BATTERY
5.CHECK DOOR CONTROL BATTERY
a.

Check door control battery operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

Collision detection door lock function operates normally.




OK

END (DOOR CONTROL BATTERY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL BATTERY)
a.

Disconnect the 2J main body ECU connector.


b.

Disconnect the E168 door control battery connector.


c.

Measure the resistance according to the value(s) in the table.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-12 - E168-8 (IG) Always Below 1 Ω
2J-12 or E168-8 (IG)) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR