In some cases, the wireless door lock control functions are normal but the hazard warning light or wireless door lock buzzer answer-back function does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU may be malfunctioning.
Start troubleshooting after confirming that the customize status of the answer-back function has been switched on.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Back Door Lock Pos SW | Back door lock position switch status / ON or OFF | ON: Back door unlocked
OFF: Back door locked |
- |
| FR Door Lock Pos | Front RH side door lock position switch signal / UNLOCK or LOCK | UNLOCK: Front RH side door unlocked
LOCK: Front RH side door locked |
- |
| FL Door Lock Pos | Front LH side door lock position switch signal / UNLOCK or LOCK | UNLOCK: Front LH side door unlocked
LOCK: Front LH side door locked |
- |
| RR-Door Lock Pos SW | Rear RH side door lock position switch signal / ON or OFF | ON: Rear RH side door unlocked
OFF: Rear RH side door locked |
- |
| RL-Door Lock Pos SW | Rear LH side door lock position switch signal / ON or OFF | ON: Rear LH side door unlocked
OFF: Rear LH side door locked |
- |
The intelligent tester display changes as shown in the table according to door lock operation.
OK
NG
Check the wireless answer-back operation using the wireless door lock control function.
| Result | Proceed to |
|---|---|
| Only hazard warning light answer-back does not occur | A |
| Only wireless door lock buzzer answer-back does not occur | B |
A
B
Check that the hazard warning lights flash continuously when the hazard warning signal switch is pressed.
Hazard warning lights flash continuously.
OK
NG
Operate the intelligent tester according to the steps on the display and select "Active Test" (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Hazard | Turn signal flasher relay | ON/OFF | - |
The hazard warning lights can be turned on and off using the intelligent tester.
OK
NG
Disconnect the E19 flasher connector.
Disconnect the E3 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E19-8 (HAZ) - E3-7 (HZSW) | Always | Below 1 Ω |
| E19-8 (HAZ) - Body ground | Always | 10 kΩ or higher |
OK
NG
Operate the intelligent tester according to the steps on the display and select "Active Test" (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | ON/OFF | - |
The wireless door lock buzzer can be turned on and off using the intelligent tester.
OK
NG
Disconnect the A20 buzzer connector.
Disconnect the E4 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A20-1 - E4-7 (BZR) | Always | Below 1 Ω |
| A20-2 - Body ground | Always | Below 1 Ω |
| A20-1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Temporarily replace the wireless door lock buzzer with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL).
NEXT
Check that the wireless door lock buzzer sounds by operating the wireless door lock function.
Wireless door lock buzzer sounds.
OK
NG