Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  TERMINALS OF ECU  


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U163117E03
2.938,2.823 2.844,2.823 2.844,2.823 2.385,2.385 true 2.948,2.594 2.854,2.594 2.854,2.594 2.396,2.156 true 2.969,0.927 2.875,0.927 2.875,0.927 2.417,1.365 true 2.958,1.375 2.865,1.375 2.865,1.375 2.406,1.813 true 5.635,1.146 5.542,1.146 5.542,1.146 5.031,0.969 true 1.552,5.104 1.927,5.333 0.375,0.229 10 false 2D 1.073,3.573 1.448,3.802 0.375,0.229 10 false 2A 4.938,1.698 5.313,1.927 0.375,0.229 10 false 2D 1.958,1.229 2.333,1.458 0.375,0.229 10 false 2C 1.948,2.094 2.323,2.323 0.375,0.229 10 false 2B 5.698,1.063 6.073,1.292 0.375,0.229 10 false 2E 2.229,2.823 2.604,3.052 0.375,0.229 10 false 2A 3.021,2.781 3.396,3.01 0.375,0.229 10 false E4 3.01,2.51 3.385,2.74 0.375,0.229 10 false E3 3.042,1.281 3.417,1.51 0.375,0.229 10 false E2 3.031,0.865 3.406,1.094 0.375,0.229 10 false E1 4.385,5.115 4.76,5.344 0.375,0.229 10 false 2E 1.042,6.969 1.417,7.198 0.375,0.229 10 false E3 6.094,5.115 6.469,5.344 0.375,0.229 10 false E4 5.99,6.969 6.365,7.198 0.375,0.229 10 false E1 3.531,6.958 3.906,7.188 0.375,0.229 10 false E2 5.615,3.563 5.99,3.792 0.375,0.229 10 false 2C 3.052,3.563 3.427,3.792 0.375,0.229 10 false 2B

a.

Disconnect the E1, E2 and 2D main body ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E1-6 (AM1) - Body ground W - Body ground +B power supply Always 11 to 14 V
E2-1 (AM2) - Body ground W - Body ground +B power supply Always 11 to 14 V
E1-17 (SSW1) - Body ground B - Body ground Engine switch 1 input Engine switch pushed Below 1 Ω
E1-17 (SSW1) - Body ground B - Body ground Engine switch 1 input Engine switch not pushed 10 kΩ or higher
E1-16 (SSW2) - Body ground B - Body ground Engine switch 2 input Engine switch pushed Below 1 Ω
E1-16 (SSW2) - Body ground B - Body ground Engine switch 2 input Engine switch not pushed 10 kΩ or higher
2D-62 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
2D-20 (LIN1) - Body ground GR - Body ground LIN line Always 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the E1, E2 and 2D main body ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E1-22 (ACCD) - 2D-62 (GND2) P - W-B ACC relay drive signal Engine switch on (ACC) 11 to 14 V
E1-22 (ACCD) - 2D-62 (GND2) P - W-B ACC relay drive signal Engine switch off Below 1 V
E1-3 (IG1D) - 2D-62 (GND2) G - W-B IG1 No. 3 relay drive signal Engine switch on (IG) 11 to 14 V
E1-3 (IG1D) - 2D-62 (GND2) G - W-B IG1 No. 3 relay drive signal Engine switch on (ACC) Below 1 V
E2-11 (IG2D) - 2D-62 (GND2) B - W-B Integration relay (IG2 relay) drive signal Engine switch on (IG) 11 to 14 V
E2-11 (IG2D) - 2D-62 (GND2) B - W-B Integration relay (IG2 relay) drive signal Engine switch on (ACC) Below 1 V
E1-19 (SLR+) - 2D-62 (GND2) G - W-B Steering lock power supply Steering lock motor operating Below 1 V
E1-19 (SLR+) - 2D-62 (GND2) G - W-B Steering lock power supply Steering lock motor not operating 11 to 14 V
E1-8 (STR) - 2D-62 (GND2) L - W-B Park/neutral position switch signal*1
Clutch pedal switch signal*2
Engine switch on (IG), shift lever not in P or N → P or N*1
Engine switch on (IG), Clutch pedal switch released → Depressed*2
Below 2 V → Pulse generation*3
E1-18 (SLP) - 2D-62 (GND2) SB - W-B Steering lock actuator position signal Steering lock locked 11 to 14 V
E1-18 (SLP) - 2D-62 (GND2) SB - W-B Steering lock actuator position signal Steering lock released Below 1 V
E3-9 (SPD) - 2D-62 (GND2) V - W-B Speed signal from combination meter Engine switch on (IG), driving wheel rotating slowly Pulse generation
(see waveform 1)
E3-8 (TACH) - 2D-62 (GND2) W - W-B Tachometer signal Engine running Pulse generation
(see waveform 2)
E4-2 (P) - 2D-62 (GND2)*1 L - W-B Shift lock signal Shift lever in P Pulse generation
(see waveform 3)
E4-2 (P) - 2D-62 (GND2)*1 L - W-B Shift lock signal Shift lever not in P Below 1 V
E4-4 (STSW) - 2D-62 (GND2) R - W-B Starter activation request signal Brake pedal depressed, engine switch depressed*1
Clutch pedal depressed, engine switch depressed*2
11 to 14 V
E1-15 (INDS) - 2D-62 (GND2) W - W-B Vehicle condition signal Brake pedal released with shift lever in P or N, engine switch off, on (ACC), or on (IG)*1
Clutch pedal released, engine switch off, on (ACC), or on (IG)*2
9 to 14 V
E1-14 (INDW) - 2D-62 (GND2) W - W-B Vehicle condition signal Brake pedal released with shift lever in P or N, engine switch off, on (ACC), or on (IG)*1
Clutch pedal released, engine switch off, on (ACC), or on (IG)*2
9 to 14 V
E1-25 (SWIL) - 2D-62 (GND2) R - W-B Illumination signal Light control switch tail or head 11 to 14 V
2B-22 (STP) - 2D-62 (GND2) R - W-B Stop light switch signal Brake pedal depressed 11 to 14 V
2B-22 (STP) - 2D-62 (GND2) R - W-B Stop light switch signal Brake pedal released Below 1 V

HINT:

*1: for A/T

*2: for M/T

*3: Remove the ST CUT relay before measuring the voltage.


If the result is not as specified, the ECU may have a malfunction.


e.

Using an oscilloscope, check the signal waveform of the ECU.

i.
C165580E06
2.885,1.844 3.302,2.042 0.417,0.198 10 false GND

Waveform 1

Reference
Terminal No. (Symbol) Tool Setting Condition
E3-9 (SPD) - 2D-62 (GND2) 5 V/DIV., 100 msec./DIV. Driving at approx. 20 km/h (12 mph)

HINT:

As the vehicle speed increases, the wavelength shortens.



ii.
C165582E14
2.906,1.115 3.323,1.313 0.417,0.198 10 false GND 0.927,1.979 2.365,2.177 1.438,0.198 10 false Engine switch on (IG) 1.167,4.24 2.458,4.438 1.292,0.198 10 false Engine started 2.906,3.385 3.323,3.583 0.417,0.198 10 false GND

Waveform 2

Reference
Terminal No. (Symbol) Tool Setting Condition
E3-8 (TACH) - 2D-62 (GND2) 10 V/DIV., 10 msec./DIV. Engine switch on (IG) or engine started


iii.
C165581E03
2.896,2.26 3.313,2.458 0.417,0.198 10 false GND

Waveform 3

Reference
Terminal No. (Symbol) Tool Setting Condition
E4-2 (P) - 2D-62 (GND2) 2 V/DIV., 20 msec./DIV. Shift lever in P




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U164611E02
3.406,0.26 3.781,0.49 0.375,0.229 10 false E29

a.

Disconnect the E29 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E29-1 (+B) - Body ground B - Body ground +B power supply Always 11 to 14 V
E29-10 (LIN) - Body ground GR - Body ground LIN line Always 10 kΩ or higher
E29-17 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the E29 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E29-18 (IG) - Body ground B - Body ground Ignition power supply Engine switch on (IG) 11 to 14 V
E29-18 (IG) - Body ground B - Body ground Ignition power supply Engine switch off Below 1 V

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.



CHECK ECM


a.

for LHD:

Disconnect the A38 and C45 ECM connectors.

U165845E02
2.344,0.135 2.667,0.333 0.323,0.198 10 false C45 5.583,0.146 5.906,0.344 0.323,0.198 10 false A38 0.208,0.01 1.063,0.25 0.854,0.24 12 false for LHD:


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-1 (BATT) - C45-81 (E1)*1, *2, *3
A38-20 (BATT) - C45-81 (E1)*4, *5
L - BR*1, *2, *4, *5
L - W-B*3
Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A38-3 (+B) - C45-81 (E1)*1, *2, *3
A38-2 (+B) - C45-81 (E1)*4, *5
B - BR*1, *2, *4, *5
B - W-B*3
Power source of ECM Engine switch on (IG) 11 to 14 V
A38-28 (IGSW) - C45-81 (E1) B - BR*1, *2, *4, *5
B - W-B*3
Engine switch signal Always 11 to 14 V
C45-81 (E1) - Body ground BR - Body ground*1, *2, *4, *5
W-B - Body ground*3
Ground Always Below 1 Ω
C45-43 (E01) - Body ground*1, *2, *3
C45-22 (E01) - Body ground*4, *5
W-B - Body ground Ground Always Below 1 Ω
C45-42 (E02) - Body ground*1, *2, *3
C45-21 (E02) - Body ground*4, *5
BR - Body ground Ground Always Below 1 Ω
C45-46 (E03) - Body ground*1, *2, *3 W-B - Body ground Ground Always Below 1 Ω
C45-23 (E04) - Body ground*1, *2, *3
C45-44 (E04) - Body ground*5
W-B - Body ground*1, *2, *3
BR - Body ground*5
Ground Always Below 1 Ω
C45-21 (E05) - Body ground*1, *2, *3
C45-23 (E05) - Body ground*5
W-B - Body ground Ground Always Below 1 Ω

HINT:

*1: for 1UR-FE

*2: for 1GR-FE

*3: for 3UR-FE

*4: for 1VD-FTV w/o DPF

*5: for 1VD-FTV w/DPF


If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the ECM connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-46 (STA) - C45-81 (E1)*1, *2, *3, *6
A38-48 (STA) - C45-81 (E1)*4, *5
R - BR*1, *2, *4, *5
R - W-B*3
R-B - BR*6
ST relay operation signal Cranking 5.5 V or more
A38-14 (STSW) - C45-81 (E1)*1, *2, *3, *4, *6
A38-47 (STSW) - C45-81 (E1)*5
R - BR*1, *2, *4, *5, *6
R - W-B*3
Starter activation request signal Brake pedal depressed, engine switch on (IG) Output voltage at terminal AM1 or AM2 is -2 V or more
A38-41 (ACCR) - C45-81 (E1)*1, *2, *3, *6
A38-13 (ACCR) - C45-81 (E1)*4
A38-22 (ACCR) - C45-81 (E1)*5
L-Y - BR*1, *2, *4, *5, *6
L-Y - W-B*3
ACC relay cut signal
(output)
Engine switch on (IG) → Cranking 11 to 14 V → Below 1 V
A38-15 (TACH) - C45-81 (E1) W - BR*1, *2, *4, *5
W - W-B*3
W-G - BR*6
Engine speed signal
(output)
Idling Pulse generation
(see waveform 1)
C45-16 (STAR) - C45-81 (E1)*1, *2, *3, *6
C45-51 (STAR) - C45-81 (E1)*4
C45-52 (STAR) - C45-81 (E1)*5
L - BR*1, *2, *4, *5, *6
L - W-B*3
ST relay drive signal Cranking 11 to 14 V

HINT:

*1: for 1UR-FE (except URJ202L-GNTEKC)

*2: for 1GR-FE (except GRJ200L-GNANKC)

*3: for 3UR-FE

*4: for 1VD-FTV w/o DPF

*5: for 1VD-FTV w/ DPF

*6: for GRJ200L-GNANKC, URJ202L-GNTEKC


If the result is not as specified, the ECM may have a malfunction.


e.
B449339E01
0.146,1.844 0.667,2.031 0.521,0.188 10 false Ground

Using an oscilloscope, check the signal waveform of the ECM.

Reference
Terminal No. (Symbol) Tool Setting Condition
A38-15 (TACH) - C45-81 (E1) 5 V/DIV., 10 ms./DIV. Engine idling

HINT:

As the engine speed increases, the wavelength shortens.



f.

for RHD:

Disconnect the A52 and C46 ECM connectors.

U165846E02
2.323,0.135 2.646,0.333 0.323,0.198 10 false C46 5.583,0.135 5.906,0.333 0.323,0.198 10 false A52 0.156,0.052 1.406,0.292 1.25,0.24 12 false for RHD:


g.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A52-1 (BATT) - C46-81 (E1)*1. *2
A52-20 (BATT) - C46-81 (E1)*3, *4
L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A52-3 (+B) - C46-81 (E1)*1, *2
A52-2 (+B) - C46-81 (E1)*3, *4
B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A52-28 (IGSW) - C46-81 (E1) B - BR Engine switch signal Always 11 to 14 V
C46-81 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
C46-43 (E01) - Body ground*1, *2
C46-22 (E01) - Body ground*3, *4
W-B - Body ground Ground Always Below 1 Ω
C46-42 (E02) - Body ground*1, *2
C46-21 (E02) - Body ground*3, *4
BR - Body ground Ground Always Below 1 Ω
C46-46 (E03) - Body ground*1, *2 W-B - Body ground Ground Always Below 1 Ω
C46-23 (E04) - Body ground*1, *2
C46-44 (E04) - Body ground*4
W-B - Body ground*1, *2
BR - Body ground*4
Ground Always Below 1 Ω
C46-21 (E05) - Body ground*1, *2
C46-23 (E05) - Body ground*4
W-B - Body ground Ground Always Below 1 Ω

HINT:

*1: for 1UR-FE

*2: for 1GR-FE

*3: for 1VD-FTV w/o DPF

*4: for 1VD-FTV w/ DPF


If the result is not as specified, there may be a malfunction on the wire harness side.


h.

Reconnect the ECM connectors.


i.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A52-46 (STA) - C46-81 (E1)*1, *2, *5
A52-48 (STA) - C46-81 (E1)*3, *4
R - BR*1, *2, *3, *4
R-B - BR*5
ST relay operation signal Cranking 5.5 V or more
A52-14 (STSW) - C46-81 (E1)*1, *2, *3, *5
A52-47 (STSW) - C46-81 (E1)*4
R - BR Starter activation request signal Brake pedal depressed, engine switch on (IG) Output voltage at terminal AM1 or AM2 is -2 V or more
A52-41 (ACCR) - C46-81 (E1)*1, *2, *5
A52-13 (ACCR) - C46-81 (E1)*3
A52-22 (ACCR) - C46-81 (E1)*4
L-Y - BR ACC relay cut signal
(output)
Engine switch on (IG) → Cranking 11 to 14 V → Below 1 V
A52-15 (TACH) - C46-81 (E1) W - BR*1, *2, *3, *4
W-G - BR*5
Engine speed signal
(output)
Idling Pulse generation
(see waveform 1)
C46-16 (STAR) - C46-81 (E1)*1, *2, *5
C46-51 (STAR) - C46-81 (E1)*3
C46-52 (STAR) - C46-81 (E1)*4
L - BR ST relay drive signal Cranking 11 to 14 V

HINT:

*1: for 1UR-FE (except URJ202L-GNTEKC)

*2: for 1GR-FE (except GRJ200L-GNANKC)

*3: for 1VD-FTV w/o DPF

*4: for 1VD-FTV w/ DPF

*5: for GRJ200L-GNANKC, URJ202L-GNTEKC


If the result is not as specified, the ECM may have a malfunction.


j.
B449339E01
0.146,1.844 0.667,2.031 0.521,0.188 10 false Ground

Using an oscilloscope, check the signal waveform of the ECM.

Reference
Terminal No. (Symbol) Tool Setting Condition
A52-15 (TACH) - C46-81 (E1) 5 V/DIV., 10 ms./DIV. Engine idling

HINT:

As the engine speed increases, the wavelength shortens.




CHECK STEERING LOCK ECU


U163842E02
3.458,0.375 3.833,0.604 0.375,0.229 10 false E26

a.

Disconnect the E26 steering lock ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E26-7 (B) - Body ground R - Body ground +B power supply Always 11 to 14 V
E26-6 (IG2) - Body ground B - Body ground Ignition power supply Engine switch on (IG) 11 to 14 V
E26-6 (IG2) - Body ground B - Body ground Ignition power supply Engine switch off Below 1 V
E26-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
E26-2 (SGND) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the E26 steering lock ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E26-4 (SLP1) - E26-1 (GND) SB - W-B Steering lock actuator position signal Steering locked 11 to 14 V
E26-4 (SLP1) - E26-1 (GND) SB - W-B Steering lock actuator position signal Steering released Below 1 V

If the result is not as specified, the ECU may have a malfunction.