Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when the IG output circuits inside the main body ECU are open or shorted.

DTC Code Detection Condition Trouble Area
B2271 The IG1 No. 3 relay actuation circuit or integration relay (IG2 relay) actuation circuit inside the main body ECU is abnormal.
·

Main body ECU


·

AM2 fuse


·

Harness or connector



WIRING DIAGRAM

B449340E01
0.542,1.323 1.344,1.521 0.802,0.198 10 false from Battery 2.719,1.51 3.073,1.729 0.354,0.219 10 false AM2 4.854,1.167 4.979,1.375 0.125,0.208 10 false 6 4.854,1.615 4.979,1.823 0.125,0.208 10 false 1 4.823,2.083 5.073,2.271 0.25,0.188 10 false 62 4.813,1.333 5.031,1.51 0.219,0.177 10 false E1 4.813,1.802 5.031,1.979 0.219,0.177 10 false E2 4.833,2.271 5.115,2.448 0.281,0.177 10 false 2D 5.135,1.313 5.552,1.5 0.417,0.188 10 false AM1 5.146,1.781 5.563,1.969 0.417,0.188 10 false AM2 5.135,2.271 5.552,2.458 0.417,0.188 10 false GND2 5.021,2.875 6.51,3.365 1.49,0.49 10 false Main Body ECU (Cowl Side Junction Block LH)

PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS

b.

Check whether DTC B2271 is output.

Result
Result Proceed to
DTC B2271 output A
No DTC output B



A

2.INSPECT FUSE (AM2)

B

2.INSPECT FUSE (AM2)
a.

Remove the AM2 fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AM2 fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
U163020E02
4.292,2.313 4.385,2.313 4.385,2.313 4.729,1.583 true 1.885,1.979 1.969,1.979 1.969,1.979 2.208,1.656 true 1.667,1.208 1.573,1.208 1.573,1.208 1.344,1.531 true 0.813,0.854 1.188,1.083 0.375,0.229 10 false E1 2.646,0.865 3.021,1.094 0.375,0.229 10 false E2 5.135,0.854 5.51,1.083 0.375,0.229 10 false 2D 2.365,0.042 4.771,0.406 2.406,0.365 10 false Front view of wire harness connector: (to Main Body ECU) 1.719,1.146 2.104,1.344 0.385,0.198 10 false AM1 1.573,1.885 1.958,2.083 0.385,0.198 10 false AM2 3.896,2.219 4.333,2.417 0.438,0.198 10 false GND2

a.

Disconnect the E1, E2 and 2D main body ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E1-6 (AM1) - Body ground Always 11 to 14 V
E2-1 (AM2) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
2D-62 (GND2) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR