Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2271 When either of the following conditions is met (1-trip detection logic*1):
·

The IG circuit in the certification ECU (smart key ECU assembly) is malfunctioning.*2

·

The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.*3


·

AM2 fuse

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


IG ON

*1: Only detected while a malfunction is present and the engine switch is on (IG).

*2: The IG circuits activate the IG relay.

*3: After the IG circuit turns on, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit maintains the power source mode in on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine switch cannot be turned on (IG) (the engine cannot be started). The power source mode cannot be changed to on (IG).

WIRING DIAGRAM

C339124E05
0.167,1.438 1.01,1.677 0.844,0.24 10 false from Battery 1.385,1.604 1.708,1.76 0.323,0.156 10 false AM2 1.823,1.448 2.323,1.604 0.5,0.156 10 false E130 2.24,1.448 2.74,1.604 0.5,0.156 10 false +B 2.375,2.458 2.875,2.615 0.5,0.156 10 false IC 2.792,2.021 3.292,2.177 0.5,0.156 10 false +B 1.896,1.25 2.396,1.406 0.5,0.156 10 false 10 3.323,2.531 3.823,2.688 0.5,0.156 10 false E128 2.917,2.427 3.417,2.583 0.5,0.156 10 false IG1D 3.448,2.333 3.948,2.49 0.5,0.156 10 false 3 3.875,2.531 4.375,2.688 0.5,0.156 10 false 2I 3.854,2.333 4.354,2.49 0.5,0.156 10 false 18 3.823,3.125 4.323,3.281 0.5,0.156 10 false 2H 3.833,2.927 4.333,3.083 0.5,0.156 10 false 17 3.844,3.75 4.344,3.906 0.5,0.156 10 false 2H 3.854,3.552 4.354,3.708 0.5,0.156 10 false 18 3.979,5.417 4.479,5.573 0.5,0.156 10 false 1X 4.042,5.24 4.542,5.396 0.5,0.156 10 false 1 4,5.781 4.5,5.938 0.5,0.156 10 false 1R 4.052,5.615 4.552,5.771 0.5,0.156 10 false 2 4.333,5.563 5.021,5.719 0.688,0.156 10 false IG2 MAIN 5.01,6.104 5.698,6.26 0.688,0.156 10 false IG2 MAIN 4.802,6.365 5.99,6.594 1.188,0.229 10 false Integration Relay 5.802,5.531 6.479,5.865 0.677,0.333 10 false ENG-IG2 NO.1 6.594,5.438 6.979,5.594 0.385,0.156 10 false 1P 6.646,5.25 6.99,5.406 0.344,0.156 10 false 7 6.594,5.781 6.958,5.938 0.365,0.156 10 false 1S 6.646,5.604 6.979,5.76 0.333,0.156 10 false 4 4.781,6.813 5.281,6.969 0.5,0.156 10 false 3 4.781,7.156 5.281,7.313 0.5,0.156 10 false 1 5.542,6.802 6.052,6.979 0.51,0.177 10 false 5 5.542,7.156 6.042,7.313 0.5,0.156 10 false 2 5.104,7.594 5.604,7.75 0.5,0.156 10 false IG1 5.625,0.635 6.604,0.823 0.979,0.188 10 false SFT-LOCK-IG 5.958,2.26 6.542,2.615 0.583,0.354 10 false ECU-IG NO.3 5.99,3.708 6.49,3.969 0.5,0.26 10 false WIPER 4.927,1.354 5.719,1.51 0.792,0.156 10 false IG1 NO.1 4.99,2.865 5.781,3.021 0.792,0.156 10 false IG1 NO.2 4.969,4.375 5.76,4.531 0.792,0.156 10 false IG1 NO.3 4.521,4.625 6.573,4.781 2.052,0.156 10 false Cowl Side Junction Block LH 6.708,0.5 7.031,0.656 0.323,0.156 10 false 2I 6.688,0.302 6.896,0.458 0.208,0.156 10 false 29 6.719,2.125 7.073,2.281 0.354,0.156 10 false 2I 6.708,1.927 6.917,2.083 0.208,0.156 10 false 33 6.708,3.563 7.073,3.719 0.365,0.156 10 false 2I 6.688,3.375 6.896,3.531 0.208,0.156 10 false 11 6.708,4.052 7.073,4.208 0.365,0.156 10 false 2J 6.729,3.865 6.938,4.021 0.208,0.156 10 false 1 3.854,0.5 4.354,0.656 0.5,0.156 10 false 2G 3.896,0.302 4.396,0.458 0.5,0.156 10 false 1 1.813,6.26 2.313,6.417 0.5,0.156 10 false E130 1.896,6.844 3.417,7.281 1.521,0.438 10 false Certification ECU (Smart Key ECU Assembly) 2.198,6.26 2.698,6.417 0.5,0.156 10 false E 1.906,6.063 2.406,6.219 0.5,0.156 10 false 11 0.063,0.063 1.198,0.458 1.135,0.396 12 false for RHD:

C339124E04
0.11,1.406 0.950,1.564 0.839,0.158 10 from Battery 1.343,1.607 1.669,1.765 0.326,0.158 10 AM2 1.817,1.43 2.319,1.589 0.501,0.158 10 E130 2.235,1.43 2.737,1.589 0.501,0.158 10 +B 2.357,2.44 2.858,2.598 0.501,0.158 10 IC 2.838,2.01 3.339,2.168 0.501,0.158 10 +B 1.927,1.246 2.428,1.404 0.501,0.158 10 10 2.932,2.441 3.434,2.600 0.501,0.158 10 IG1D 3.451,2.329 3.952,2.488 0.501,0.158 10 3 3.879,2.52 4.381,2.678 0.501,0.158 10 2I 3.326,2.52 3.827,2.678 0.501,0.158 10 E128 3.851,2.337 4.353,2.496 0.501,0.158 10 18 3.823,3.119 4.324,3.278 0.501,0.158 10 2H 3.837,2.923 4.339,3.082 0.501,0.158 10 17 3.837,3.751 4.339,3.910 0.501,0.158 10 2H 3.851,3.555 4.353,3.714 0.501,0.158 10 18 3.998,5.416 4.499,5.575 0.501,0.158 10 1Y 4.054,5.22 4.556,5.379 0.501,0.158 10 1 4.003,5.776 4.504,5.934 0.501,0.158 10 1R 4.054,5.606 4.556,5.764 0.501,0.158 10 2 4.329,5.562 5.015,5.720 0.687,0.158 10 IG2 MAIN 4.979,6.063 5.666,6.221 0.687,0.158 10 IG2 MAIN 4.79,6.336 6.042,6.495 1.253,0.158 10 Integration Relay 5.788,5.525 6.479,5.867 0.691,0.342 10 ENG-IG2 NO.1 6.601,5.422 6.991,5.581 0.390,0.158 10 1P 6.643,5.212 6.984,5.371 0.342,0.158 10 7 6.605,5.768 6.971,5.926 0.366,0.158 10 1S 6.643,5.598 6.974,5.756 0.331,0.158 10 4 4.784,6.802 5.285,6.961 0.501,0.158 10 3 4.784,7.153 5.285,7.311 0.501,0.158 10 1 5.54,6.802 6.042,6.961 0.501,0.158 10 5 5.54,7.153 6.042,7.311 0.501,0.158 10 2 5.078,7.61 5.580,7.769 0.501,0.158 10 IG1 5.627,0.6 6.601,0.792 0.974,0.191 10 SFT-LOCK-IG 5.956,2.23 6.542,2.584 0.586,0.354 10 ECU-IG NO.3 5.928,3.689 6.565,4.025 0.637,0.336 10 WIPER 4.926,1.359 5.715,1.518 0.789,0.158 10 IG1 NO.1 4.903,2.868 5.691,3.026 0.789,0.158 10 IG1 NO.2 4.92,4.341 5.709,4.499 0.789,0.158 10 IG1 NO.3 4.517,4.625 6.565,4.784 2.048,0.158 10 Cowl Side Junction Block LH 6.705,0.482 7.026,0.641 0.321,0.158 10 2I 6.691,0.3 6.897,0.459 0.205,0.158 10 29 6.719,2.111 7.073,2.270 0.353,0.158 10 2I 6.705,1.929 6.911,2.087 0.205,0.158 10 33 6.705,3.557 7.073,3.716 0.367,0.158 10 2I 6.691,3.361 6.897,3.520 0.205,0.158 10 11 6.705,4.034 7.073,4.192 0.367,0.158 10 2J 6.748,3.866 6.953,4.024 0.205,0.158 10 1 3.853,0.476 4.354,0.635 0.501,0.158 10 2G 3.909,0.294 4.410,0.453 0.501,0.158 10 1 1.808,6.255 2.310,6.413 0.501,0.158 10 E130 1.899,6.88 3.500,7.285 1.601,0.405 10 Certification ECU (Smart Key ECU Assembly) 2.196,6.265 2.698,6.423 0.501,0.158 10 E 1.907,6.061 2.408,6.219 0.501,0.158 10 11 0.087,0.033 0.860,0.301 0.773,0.268 12 for LHD:

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


Click here


HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2271
Power Source Control
·

IG Relay Monitor (Inside)

·

Latch Circuit


Starting Control
·

Ignition


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.
U164305E01
0.14,0.101 0.326,0.259 0.186,0.158 10 *a 2.729,3.919 3.225,4.078 0.497,0.158 10 +B 2.446,3.457 2.553,3.985 2.553,3.985 2.676,3.985 false 1.598,2.202 2.011,2.360 0.413,0.158 10 E130

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E130-10 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (smart key ECU assembly))



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.
U164306E01
0.14,0.101 0.326,0.259 0.186,0.158 10 *a 0.52,4.061 0.888,4.220 0.368,0.158 10 E 0.907,3.608 0.812,4.128 0.812,4.128 0.694,4.128 false 1.598,2.202 2.011,2.360 0.413,0.158 10 E130

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-11 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (smart key ECU assembly))



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the E130 certification ECU (smart key ECU assembly) connector.


b.
U165441E01
0.078,0.031 0.266,0.189 0.189,0.158 10 *a 0.612,1.707 1.109,1.865 0.497,0.158 10 IG1D 1.242,0.899 1.151,1.796 1.151,1.796 1.016,1.796 false 1.481,0.126 1.894,0.284 0.413,0.158 10 E128

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E128-3 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)