Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2272  Ignition 1 Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction occurs in the IG1D output circuit, which is between the IG1 No. 3 relay actuation circuit inside the main body ECU and the IG1 No. 3 relay.

DTC Code Detection Condition Trouble Area
B2272 The IG1 No. 3 relay actuation circuit inside the main body ECU or other related circuit is malfunctioning.
·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

C164716E04
4.014,1.91 5.022,2.095 1.008,0.185 10 ECU-IG No. 2 3.028,2.508 3.843,2.692 0.815,0.185 10 IG1 No. 3 0.545,1.763 1.402,1.948 0.856,0.185 10 from Battery 2.12,1.763 2.428,1.948 0.308,0.185 10 2A 2.124,3.856 2.432,4.041 0.308,0.185 10 E1 5.767,2.178 6.032,2.363 0.265,0.185 10 2D 5.791,1.971 6.056,2.156 0.265,0.185 10 62 2.12,2.178 2.385,2.363 0.265,0.185 10 2D 2.139,1.987 2.404,2.172 0.265,0.185 10 43 2.174,3.651 2.338,3.836 0.164,0.185 10 3 2.171,1.556 2.335,1.741 0.164,0.185 10 1 2.43,3.856 2.823,4.041 0.392,0.185 10 IG1D 3.348,3.856 3.570,4.041 0.222,0.185 10 IG 5.283,2.294 5.717,2.479 0.434,0.185 10 GND2 2.547,4.917 6.025,5.102 3.478,0.185 10 Main Body ECU (Cowl Side Junction Block LH) 3.603,3.955 3.825,4.140 0.222,0.185 10 15

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG1 RELAY MONITOR (OUTSIDE))
a.

Use the Data List to check if the IG1 No. 3 relay is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG1 Relay Monitor (Outside) IG1 No. 3 relay outer relay monitor/ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-

OK:

When the engine switch is turned on (IG), ON is displayed on the intelligent tester.




OK

2.CHECK WHETHER DTC OUTPUT RECURS

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
2.CHECK WHETHER DTC OUTPUT RECURS

b.

Turn the engine switch on (IG), wait at least 10 seconds, and check whether DTC B2272 is output.

Result
Result Proceed to
No DTC output A
DTC B2272 output B



A

B

REPLACE MAIN BODY ECU

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
U163021E01
0.918,0.873 1.293,1.106 0.375,0.233 10 E1 2.618,0.873 2.993,1.106 0.375,0.233 10 2A 5.158,0.873 5.533,1.106 0.375,0.233 10 2D 2.347,0.048 4.756,0.415 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 0.04,1.069 0.434,1.271 0.394,0.202 10 IG1D 3.648,2.221 4.082,2.423 0.434,0.202 10 GND2 0.404,1.16 0.476,1.16 0.476,1.16 0.93,1.566 false 4.094,2.314 4.181,2.314 4.181,2.314 4.651,1.597 false

a.

Disconnect the E1, 2A and 2D main body ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2A-1 - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
E1-3 (IG1D) - 2D-43 Always Below 1 Ω
2D-62 (GND2) - Body ground Always Below 1 Ω
E1-3 (IG1D) or 2D-43 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR