Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2273  Ignition 2 Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction occurs in the IG2D output circuit, which is between the integration relay (IG2 relay) actuation circuit inside the main body ECU and the integration relay (IG2 relay).

DTC Code Detection Condition Trouble Area
B2273 The integration relay (IG2 relay) actuation circuit inside the main body ECU or other related circuit is malfunctioning.
·

Main body ECU

·

IG2 MAIN fuse

·

Integration relay (IG2 relay)

·

Harness or connector



WIRING DIAGRAM

C357843E01
1.063,0.531 3.292,0.917 2.229,0.385 10 false to Steering Lock Actuator Assembly (Steering Lock ECU) 0.333,1.688 1.146,1.948 0.813,0.26 10 false from Battery 2.094,1.49 2.271,1.688 0.177,0.198 10 false 1 2.125,2.323 2.302,2.521 0.177,0.198 10 false 7 2.052,1.698 2.354,1.875 0.302,0.177 10 false 1C 2.073,2.104 2.375,2.281 0.302,0.177 10 false 1B 2.406,1.854 2.833,2.156 0.427,0.302 10 false IG2 MAIN 3.01,2.458 3.427,2.625 0.417,0.167 10 false IG2 2.417,2.792 3.656,2.969 1.24,0.177 10 false Integration Relay 3.688,1.688 3.99,1.865 0.302,0.177 10 false 1B 3.719,1.49 3.896,1.688 0.177,0.198 10 false 8 3.688,2.115 3.99,2.292 0.302,0.177 10 false 1B 3.75,2.302 3.927,2.5 0.177,0.198 10 false 6 4.688,2.24 4.927,2.438 0.24,0.198 10 false 11 4.99,2.125 5.646,2.417 0.656,0.292 10 false IG2D 4.281,3 4.521,3.198 0.24,0.198 10 false E2 4.281,3.156 7.125,3.406 2.844,0.25 10 false Main Body ECU (Cowl Side Junction Block LH)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG2 RELAY MONITOR (INSIDE))
a.

Use the Data List to check if the integration relay (IG2 relay) is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG2 Relay Monitor (Inside) Integration relay (IG2 relay) inner relay monitor/ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-

OK:

When the engine switch is turned on (IG), ON is displayed on the tester.




OK

2.CHECK WHETHER DTC OUTPUT RECURS

NG

3.INSPECT FUSE (IG2 MAIN)
2.CHECK WHETHER DTC OUTPUT RECURS

b.

Turn the engine switch on (IG), wait at least 10 seconds, and check whether DTC B2273 is output.

Result
Result Proceed to
No DTC output A
DTC B2273 output B



A

B

REPLACE MAIN BODY ECU

3.INSPECT FUSE (IG2 MAIN)
a.

Remove the IG2 MAIN fuse from the integration relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 MAIN fuse Always Below 1 Ω




OK

4.INSPECT INTEGRATION NO.1 RELAY (IG2 RELAY)

NG

REPLACE FUSE (IG2 MAIN)

4.INSPECT INTEGRATION NO.1 RELAY (IG2 RELAY)
U163036E02
0.167,0.177 2.667,0.552 2.5,0.375 10 false Component without harness connected: (Integration Relay) 2.635,2.604 2.885,2.792 0.25,0.188 10 false 1A 1.313,2.615 1.563,2.802 0.25,0.188 10 false 1B 0.396,2.615 0.646,2.802 0.25,0.188 10 false 1C

a.

Install the IG2 MAIN fuse to the integration relay.


b.

Remove the integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-8 - 1C-1 Battery voltage applied to terminals 1B-6 and 1B-7 Below 1 Ω
1B-8 - 1C-1 Battery voltage not applied to terminals 1B-6 and 1B-7 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)

NG

REPLACE INTEGRATION NO.1 RELAY (IG2 RELAY)

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)
U163038E01
1.629,0.947 2.004,1.180 0.375,0.233 10 E2 5.128,0.947 5.502,1.180 0.375,0.233 10 1B 0.519,0 2.927,0.367 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 4.034,0 6.441,0.367 2.408,0.367 10 Front view of wire harness connector: (to Integration Relay) 0.323,2.122 0.728,2.323 0.405,0.202 10 IG2D 0.726,2.216 0.813,2.216 0.813,2.216 1.231,1.902 false

a.

Disconnect the E2 main body ECU connector.


b.

Disconnect the 1B integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2-11 (IG2D) - 1B-6 Always Below 1 Ω
1B-7 - Body ground Always Below 1 Ω
E2-11 (IG2D) or 1B-6 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR