Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2278  Engine Switch Circuit Malfunction  


DESCRIPTION

This DTC is stored when: 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.

DTC Code Detection Condition Trouble Area
B2278 Communication is abnormal between the main body ECU and engine switch or the engine switch is defective.
·

Main body ECU

·

Engine switch

·

Harness or connector



WIRING DIAGRAM

C357848E01
3.198,1.219 3.656,1.417 0.458,0.198 10 false SS1 3.177,2.146 3.635,2.344 0.458,0.198 10 false SS2 2.125,2.135 2.583,2.333 0.458,0.198 10 false GND 2.458,2.719 2.917,2.917 0.458,0.198 10 false E18 2.458,2.885 3.708,3.323 1.25,0.438 10 false Engine Switch 4.958,2.813 5.417,3.01 0.458,0.198 10 false E1 4.958,2.958 6.448,3.688 1.49,0.729 10 false Main Body ECU (Cowl Side Junction Block LH) 3.594,1.469 4.052,1.667 0.458,0.198 10 false 7 3.573,2.375 4.031,2.573 0.458,0.198 10 false 2 4.896,1.458 5.354,1.656 0.458,0.198 10 false 17 4.885,2.396 5.344,2.594 0.458,0.198 10 false 16 5.135,1.344 5.76,1.604 0.625,0.26 10 false SSW1 5.146,2.26 5.771,2.521 0.625,0.26 10 false SSW2

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (START SWITCH 1, 2)
a.

Use the Data List to check if the engine switch is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Start Switch 1 Start Switch 1/ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
Start Switch 2 Start Switch 2/ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-

OK:

When the engine switch is turned on (IG), ON is displayed on the intelligent tester.




OK

2.CHECK WHETHER DTC OUTPUT RECURS

NG

3.INSPECT ENGINE SWITCH
2.CHECK WHETHER DTC OUTPUT RECURS

b.

Turn the engine switch on (IG), and check whether DTC B2278 is output.

Result
Result Proceed to
No DTC output A
DTC B2278 output B



A

B

REPLACE MAIN BODY ECU

3.INSPECT ENGINE SWITCH
C164809E03
0.186,0.376 2.717,0.743 2.531,0.367 10 Component without harness connected: (Engine Switch) 0.227,1.421 0.603,1.623 0.376,0.202 10 GND 0.307,1.775 0.649,1.977 0.341,0.202 10 SS1 2.814,1.775 3.155,1.977 0.341,0.202 10 SS2 0.669,1.537 0.776,1.537 0.776,1.537 1.551,2.131 false 0.669,1.892 0.776,1.892 0.776,1.892 1.216,2.131 false 2.764,1.892 2.657,1.892 2.657,1.892 2.054,2.131 false

a.

Disconnect the E18 engine switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (SS1) - 5 (GND) Pushed Below 1 Ω
2 (SS2) - 5 (GND) Pushed Below 1 Ω
7 (SS1) - 5 (GND) Not pushed 10 kΩ or higher
2 (SS2) - 5 (GND) Not pushed 10 kΩ or higher


Result
Result Proceed to
Within specified range A
Outside specified range (for 1GR-FE) B
Outside specified range (for 1UR-FE) C
Outside specified range (for 3UR-FE) D
Outside specified range (for 1VD-FTV) E



A

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE SWITCH AND BODY GROUND)

B

C

D

E

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE SWITCH AND BODY GROUND)
U164584E02
2.802,2.417 2.708,2.417 2.708,2.417 2.281,1.917 true 2.802,2.115 2.708,2.115 2.708,2.115 2.365,1.896 true 6.094,1.281 6.01,1.281 6.01,1.281 5.427,1.688 true 6.083,1.594 6,1.594 6,1.594 5.656,1.708 true 4.479,1.594 4.573,1.594 4.573,1.594 5.031,1.708 true 5.167,0.906 5.542,1.135 0.375,0.229 10 false E18 1.813,0.917 2.188,1.146 0.375,0.229 10 false E1 4.063,0.063 6.469,0.427 2.406,0.365 10 false Front view of wire harness connector: (to Engine Switch) 6.156,1.177 6.531,1.375 0.375,0.198 10 false GND 4.146,1.5 4.49,1.698 0.344,0.198 10 false SS2 6.156,1.479 6.5,1.677 0.344,0.198 10 false SS1 2.833,2.01 3.271,2.208 0.438,0.198 10 false SSW1 2.854,2.302 3.292,2.5 0.438,0.198 10 false SSW2 0.656,0.063 3.063,0.427 2.406,0.365 10 false Front view of wire harness connector: (to Main Body ECU)

a.

Disconnect the E1 main body ECU connector.


b.

Disconnect the E18 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-17 (SSW1) - E18-7 (SS1) Always Below 1 Ω
E1-16 (SSW2) - E18-2 (SS2) Always Below 1 Ω
E18-5 (GND) - Body ground Always Below 1 Ω
E1-17 (SSW1) or E18-7 (SS1) - Body ground Always 10 kΩ or higher
E1-16 (SSW2) or E18-2 (SS2) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR