Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when there is an inconsistency between the circuit between the main body ECU and stop light switch, and the CAN communication signal between the main body ECU and ECM.

DTC No. Detection Condition Trouble Area
B2284 The circuit between the main body ECU and stop light switch, and the CAN communication signal between the main body ECU and ECM are inconsistent.
·

Main body ECU

·

Stop light switch

·

STOP fuse

·

Harness or connector



WIRING DIAGRAM

C357853E01
0.542,1.813 1.344,2.063 0.802,0.25 10 false from Battery 0.427,2.24 1.333,2.5 0.906,0.26 10 false from IG circuit 1.927,1.979 2.333,2.156 0.406,0.177 10 false STOP 2.542,1.938 2.656,2.125 0.115,0.188 10 false 2 2.552,2.354 2.667,2.542 0.115,0.188 10 false 4 3.333,2.365 3.448,2.552 0.115,0.188 10 false 3 3.323,1.917 3.438,2.104 0.115,0.188 10 false 1 3.719,2.25 4.625,2.51 0.906,0.26 10 false to ECM 5.146,1.354 6.052,1.615 0.906,0.26 10 false CAN 5.156,1.833 6.063,2.094 0.906,0.26 10 false STP 4.833,1.917 5.094,2.115 0.26,0.198 10 false 22 2.438,2.583 3.323,2.76 0.885,0.177 10 false A30 2.438,2.729 3.531,2.896 1.094,0.167 10 false Stop Light Switch 5.01,2.854 5.896,3.031 0.885,0.177 10 false 2B 5,3.021 6.51,3.375 1.51,0.354 10 false Main Body ECU (Cowl Side Junction Block LH) 0.417,3.406 2.156,3.604 1.74,0.198 10 false : CAN Communication Line

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Use the Data List to check if the stop light switch is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-

Result
Result Proceed to
Display on the intelligent tester does not change according to brake pedal operation A
Display on the intelligent tester changes according to brake pedal operation B



A

2.INSPECT FUSE (STOP)

B

REPLACE MAIN BODY ECU

2.INSPECT FUSE (STOP)
a.

Remove the STOP fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
STOP fuse Always Below 1 Ω




OK

3.INSPECT STOP LIGHT SWITCH

NG

REPLACE FUSE

3.INSPECT STOP LIGHT SWITCH
A175403E01
0.074,0 2.652,0.399 2.578,0.399 10 Component without harness connected: (Stop Light Switch) 1.102,2.975 1.907,3.149 0.804,0.174 10 Not Pushed 0.95,2.493 1.422,2.263 1.422,2.263 1.627,2.263 false 1.102,2.569 1.661,2.743 0.559,0.174 10 Pushed 1.685,2.151 2.429,2.325 0.744,0.175 10 Switch Pin

a.

Disconnect the A30 stop light switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Stop light switch pin not pushed Below 1 Ω
3 - 4 Stop light switch pin pushed Below 1 Ω
1 - 2 Stop light switch pin pushed 10 kΩ or higher
3 - 4 Stop light switch pin not pushed 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND STOP LIGHT SWITCH)

NG

REPLACE STOP LIGHT SWITCH

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND STOP LIGHT SWITCH)
U163028E01
2.184,0.872 2.559,1.105 0.375,0.233 10 2B 5.41,0.878 5.785,1.111 0.375,0.233 10 A30 1.236,0.064 3.645,0.432 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 4.508,0.064 6.916,0.432 2.408,0.367 10 Front view of wire harness connector: (to Stop Light Switch) 3.346,2.222 3.690,2.424 0.344,0.202 10 STP 3.304,2.318 3.217,2.318 3.217,2.318 2.817,1.941 false

a.

Disconnect the 2B main body ECU connector.


b.

Disconnect the A30 stop light switch connector.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
2B-22 (STP) - A30-1 Always Below 1 Ω
2B-22 (STP) or A30-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR