Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2289  Key Collation Waiting Time Over  


DESCRIPTION

This DTC is stored when there is a LIN communication problem between the main body ECU and certification ECU (smart key ECU assembly) or when there is a problem in the engine immobiliser system.

DTC Code Detection Condition Trouble Area
B2289 When either of the following conditions is met:
·

Communication or the communication line is abnormal among the main body ECU, certification ECU (smart key ECU assembly), steering lock ECU and ID code box (immobiliser code ECU).

·

The immobiliser system malfunctions.


·

Main body ECU

·

Engine switch

·

Certification ECU (smart key ECU assembly)

·

Key

·

Engine immobiliser system

·

Harness or connector



WIRING DIAGRAM

C357845E02
1.719,1.813 2.333,2.01 0.615,0.198 10 false LIN 5.146,1.802 5.76,2 0.615,0.198 10 false LIN 4.854,1.906 5.01,2.125 0.156,0.219 10 false 20 2.073,1.896 3.156,2.135 1.083,0.24 10 false 10 0.833,2.833 1.75,3.01 0.917,0.177 10 false E29 0.844,2.979 2.385,3.458 1.542,0.479 10 false Certification ECU (Smart Key ECU Assembly) 4.938,2.802 5.854,2.979 0.917,0.177 10 false 2D 4.938,2.948 6.5,3.385 1.563,0.438 10 false Main Body ECU (Cowl Side Junction Block LH)

PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS

b.

Check whether DTC B2289 is output.

Result
Result Proceed to
DTC B2289 output A
No DTC output B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
U163031E01
1.708,1.043 2.083,1.276 0.375,0.233 10 2D 5.489,1.117 5.864,1.350 0.375,0.233 10 E29 0.636,0.028 3.044,0.395 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 4.393,0.028 6.802,0.527 2.408,0.499 10 Front view of wire harness connector: (to Certification ECU (Smart Key ECU Assembly)) 3.267,2.333 3.657,2.535 0.390,0.202 10 LIN1 6.725,1.097 7.115,1.299 0.390,0.202 10 LIN 6.671,1.188 6.615,1.188 6.615,1.188 5.975,1.714 false 3.226,2.426 3.196,2.426 3.196,2.426 2.865,1.869 false

a.

Disconnect the 2D main body ECU connector.


b.

Disconnect the E29 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-20 (LIN1) - E29-10 (LIN) Always Below 1 Ω
2D-20 (LIN) or E29-10 (LIN) - Body ground Always 10 kΩ or higher




OK

3.REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE MAIN BODY ECU
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check whether DTC B2289 is output.

OK:

No DTC is output.




OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)