Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Engine Switch Indicator Circuit  


DESCRIPTION

Engine switch condition (power source mode) or system malfunctions can be checked by observing the status of the engine switch indicator light.

Engine Switch Indicator Light Condition
Power Source Mode/Condition Indicator Light Condition
Brake pedal released (for A/T)
Clutch pedal released (for M/T)
Brake pedal depressed, shift lever in P or N (for A/T) Clutch pedal depressed (for M/T)
Off Off Illuminates (Green) Illuminates (Green)
On (ACC, IG) Illuminates (Amber) Illuminates (Green) Illuminates (Green)
Engine running Off Off Off
Steering lock not unlocked Flashes (Green) for 30 sec. Flashes (Green) for 30 sec. Flashes (Green) for 30 sec.
System malfunction Flashes (Amber) for 15 sec. Flashes (Amber) for 15 sec. Flashes (Amber) for 15 sec.
Clutch start switch malfunction (for M/T) Flashes (Green) for 15 sec. Flashes (Green) for 15 sec. Flashes (Green) for 15 sec.

WIRING DIAGRAM

C357868E01
1.615,1.125 2.229,1.323 0.615,0.198 10 false INDS 1.573,1.573 2.26,1.771 0.688,0.198 10 false INDW 1.573,2.042 2.26,2.24 0.688,0.198 10 false SWIL 1.615,2.5 2.302,2.698 0.688,0.198 10 false GND 2.073,1.229 2.76,1.427 0.688,0.198 10 false 12 2.073,1.677 2.76,1.875 0.688,0.198 10 false 13 2.063,2.146 2.75,2.344 0.688,0.198 10 false 11 2.073,2.615 2.76,2.813 0.688,0.198 10 false 5 4.885,1.24 5.573,1.438 0.688,0.198 10 false 15 4.885,1.708 5.573,1.906 0.688,0.198 10 false 14 4.896,2.188 5.583,2.385 0.688,0.198 10 false 25 5.167,1.115 5.781,1.313 0.615,0.198 10 false INDS 5.167,1.583 5.781,1.781 0.615,0.198 10 false INDW 5.167,2.021 5.781,2.219 0.615,0.198 10 false SWIL 1.052,3.052 1.74,3.25 0.688,0.198 10 false E18 1.052,3.198 2.083,3.75 1.031,0.552 10 false Engine Switch 5,2.604 5.688,2.802 0.688,0.198 10 false E1 4.99,2.771 6.479,3.229 1.49,0.458 10 false Main Body ECU (Cowl Side Junction Block LH)

PROCEDURE

1.INSPECT ENGINE SWITCH
C164809E05
0.186,0.323 2.717,0.691 2.531,0.367 10 Component without harness connected: (Engine Switch) 0.244,1.389 0.620,1.591 0.376,0.202 10 GND 2.809,2.923 3.247,3.125 0.438,0.202 10 SWIL 0.16,2.557 0.595,2.759 0.435,0.202 10 INDW 0.216,2.923 0.650,3.125 0.435,0.202 10 INDS 0.681,3.027 0.787,3.027 0.787,3.027 1.551,2.447 false 0.681,2.672 0.787,2.672 0.787,2.672 1.383,2.447 false 0.681,1.5 0.787,1.5 0.787,1.5 1.551,2.08 false 2.757,3.027 2.65,3.027 2.65,3.027 1.724,2.447 false

a.

Disconnect the E18 engine switch connector.


b.

Apply battery voltage between the terminals of the engine switch, and check the illumination condition of the engine switch indicator light.

NOTICE:
·

If the positive (+) lead and the negative (-) lead are incorrectly connected, the engine switch indicator light will not illuminate.

·

If the voltage is too low, the indicator light will not illuminate.



OK:
Measurement Condition Condition Specified Condition
Battery terminal (+) → Terminal 11 (SWIL) - Battery terminal (-) → Terminal 5 (GND) Battery voltage is applied to the terminals Illuminates
Battery terminal (+) → Terminal 12 (INDS) - Battery terminal (-) → Terminal 5 (GND)
Battery terminal (+) → Terminal 13 (INDW) - Battery terminal (-) → Terminal 5 (GND)


Result
Result Proceed to
Illuminates A
Does not illuminate (for 1GR-FE) B
Does not illuminate (for 1UR-FE) C
Does not illuminate (for 3UR-FE) D
Does not illuminate (for 1VD-FTV) E



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE SWITCH AND BODY GROUND)

B

C

D

E

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE SWITCH AND BODY GROUND)
U164586E02
6.063,2.406 5.969,2.406 5.969,2.406 5.438,1.938 true 6.063,2.125 5.969,2.125 5.969,2.125 5.552,1.938 true 6.052,1.24 5.958,1.24 5.958,1.24 5.427,1.708 true 4.563,2.406 4.656,2.406 4.656,2.406 5.313,1.938 true 2.792,1.469 2.698,1.469 2.698,1.469 2.083,1.844 true 2.802,1.719 2.708,1.719 2.708,1.719 2.188,1.833 true 2.802,2.417 2.708,2.417 2.708,2.417 2.281,2.042 true 5.188,0.917 5.563,1.146 0.375,0.229 10 false E18 1.833,0.927 2.208,1.156 0.375,0.229 10 false E1 4.063,0.063 6.469,0.427 2.406,0.365 10 false Front view of wire harness connector: (to Engine Switch) 6.125,1.188 6.5,1.385 0.375,0.198 10 false GND 4.156,2.323 4.583,2.521 0.427,0.198 10 false SWIL 6.104,2.031 6.573,2.229 0.469,0.198 10 false INDW 6.104,2.323 6.521,2.521 0.417,0.198 10 false INDS 2.844,1.396 3.281,1.594 0.438,0.198 10 false INDW 2.844,1.656 3.281,1.854 0.438,0.198 10 false INDS 2.833,2.333 3.271,2.531 0.438,0.198 10 false SWIL 0.656,0.063 3.063,0.427 2.406,0.365 10 false Front view of wire harness connector: (to Main Body ECU)

a.

Disconnect the E1 main body ECU connector.


b.

Disconnect the E18 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-25 (SWIL) - E18-11 (SWIL) Always Below 1 Ω
E1-15 (INDS) - E18-12 (INDS) Always Below 1 Ω
E1-14 (INDW) - E18-13 (INDW) Always Below 1 Ω
E18-5 (GND) - Body ground Always Below 1 Ω
E1-25 (SWIL) or E18-11 (SWIL) - Body ground Always 10 kΩ or higher
E1-15 (INDS) or E18-12 (INDS) - Body ground Always 10 kΩ or higher
E1-14 (INDW) or E18-13 (INDW) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR