Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  U0100  Lost Communication with ECM / PCM  U0140  Lost Communication with Main Body ECU  U0142  Lost Communication with Main Body ECU  U0155  Lost Communication with Combination Meter  U1117  Lost Communication with Accessory Gateway  


DESCRIPTION

These DTCs are stored when there is a CAN communication error between the certification ECU (smart key ECU assembly) and the ECM, main body ECU (multiplex network body ECU) or combination meter assembly.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
U0100 CAN communication error between the certification ECU (smart key ECU assembly) and ECM (1-trip detection*) ECM Turn the engine switch on (IG) and wait 10 seconds or more.
U0140
U0142
CAN communication error between the certification ECU (smart key ECU assembly) and main body ECU (1-trip detection*) Main body ECU (multiplex network body ECU) Always
U0155 CAN communication error between the certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection*) Combination meter assembly Turn the engine switch on (IG) and wait 10 seconds or more.
U1117 Data from the option connector (bus buffer ECU) cannot be received.
·

Connector and branch wire of sub bus 2 of option connector (bus buffer ECU)

·

Internal malfunction of option connector (bus buffer ECU)


Turn the engine switch on (IG) and wait 10 seconds or more.

*: Only detected while a malfunction is present and the engine switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
U0100 There is no effect on vehicle behavior. If the following conditions are met, it is determined that the malfunction is not in the direct line (NE) but in CAN communication.
·

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

·

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (NE).
·

When the engine switch is pressed, the engine stops cranking after 6 seconds.

·

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.


U0140
U0142
Doors cannot be locked or unlocked. The warning (wireless buzzer) does not sound. -
U0155 The warning (meter buzzer) does not sound and the meter does not indicate a warning. -
U1117 The engine cannot be started using the wireless remote control function. -

HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
U0100
U0140
U0142
U0155
U1117
- -


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK FOR DTC
a.

Note any DTCs that are output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR).

Result
Result Proceed to
NEXT for LHD (with Central Gateway ECU) A
for LHD (without Central Gateway ECU) B
for RHD (with Central Gateway ECU) C
for RHD (without Central Gateway ECU) D



A

B

C

D