Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is built into the hood lock. This switch turns on when the engine hood is opened and turns off when the engine hood is closed.


WIRING DIAGRAM

B159038E07
4.742,1.732 6.337,2.079 1.596,0.346 10 Certification ECU (Smart Key ECU Assembly) 4.742,1.546 5.064,1.702 0.323,0.156 10 E30 1.943,1.52 3.835,1.916 1.892,0.395 10 Hood Lock Assembly (Engine Hood Courtesy Switch) 1.008,3.428 4.251,3.589 3.244,0.161 10 *2: for Hood Courtesy Switch Connector 4 Pin Type 1.008,3.11 4.193,3.271 3.186,0.161 10 *1: for Hood Courtesy Switch Connector 2 Pin Type 1.943,1.376 2.181,1.532 0.238,0.156 10 A8 4.752,1.042 5.130,1.198 0.378,0.156 10 HSW 4.42,0.925 4.623,1.081 0.202,0.156 10 24 2.907,0.934 3.023,1.090 0.116,0.156 10 2 2.013,0.777 2.242,0.933 0.229,0.156 10 1*1 2.013,0.937 2.242,1.093 0.229,0.156 10 4*2

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE HOOD COURTESY SWITCH)
a.

Using the intelligent tester, read the Data List.

Entry&Start
Tester Display Measurement Item / Display (Range) Normal Condition Diagnostic Note
Hood Courtesy Switch Engine hood courtesy switch /
ON or OFF
ON: Engine hood is open
OFF: Engine hood is closed
-

OK:

ON (engine hood is open) appears on screen.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
B219990E01
4.595,0.315 7.126,0.645 2.531,0.330 10 Component without harness connected: (Hood Lock Assembly) 0.633,2.258 1.806,2.407 1.172,0.149 10 Unlock Position 3.276,2.258 4.449,2.407 1.172,0.149 10 Lock Position 0.045,0.045 4.429,0.210 4.383,0.165 12 for Hood Courtesy Switch Connector 2 Pin Type (for LHD):

a.

for Hood Courtesy Switch Connector 2 Pin Type (for LHD):


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Unlock position 10 kΩ or higher
1 - 2 Lock position Below 1 Ω




B219989E01
4.614,0.262 7.146,0.592 2.531,0.330 10 Component without harness connected: (Hood Lock Assembly) 1.01,2.205 2.183,2.355 1.172,0.149 10 Unlock Position 3.614,2.205 4.786,2.355 1.173,0.149 10 Lock Position 0.057,0.032 4.440,0.197 4.383,0.165 12 for Hood Courtesy Switch Connector 2 Pin Type (for RHD):

b.

for Hood Courtesy Switch Connector 2 Pin Type (for RHD):


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Unlock position 10 kΩ or higher
1 - 2 Lock position Below 1 Ω




B216369E01
4.602,0.221 7.133,0.551 2.531,0.330 10 Component without harness connected: (Hood Lock Assembly) 1.005,2.33 2.000,2.479 0.994,0.149 10 Unlock Position 0.046,0.06 3.716,0.225 3.670,0.165 12 for Hood Courtesy Switch Connector 4 Pin Type: 3.602,2.33 4.537,2.479 0.935,0.149 10 Lock Position

c.

for Hood Courtesy Switch Connector 4 Pin Type:


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 4 Unlock position 10 kΩ or higher
2 - 4 Lock position Below 1 Ω





OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - HOOD LOCK AND BODY GROUND)

NG

REPLACE HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - HOOD LOCK AND BODY GROUND)
U164009E01
0.119,2.552 2.469,2.874 2.350,0.323 10 Front view of wire harness connector: (to Hood Lock) 0.119,0.001 2.485,0.499 2.367,0.498 10 Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 0.872,3.815 1.097,3.965 0.225,0.150 10 A8 0.234,1.524 0.570,1.674 0.336,0.150 10 E30 2.323,2.217 2.691,2.401 0.369,0.184 10 HSW 2.519,1.808 2.519,2.205 false

a.

for Hood Courtesy Switch Connector 2 Pin Type:

i.

Disconnect the E30 ECU connector.


ii.

Disconnect the A8 switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E30-24 (HSW) - A8-2 Always Below 1 Ω
A8-1 - Body ground Always Below 1 Ω
E30-24 (HSW) or A8-2 - Body ground Always 10 kΩ or higher




U164151E01
0.119,2.579 2.469,2.901 2.350,0.323 10 Front view of wire harness connector: (to Hood Lock) 0.119,0.028 2.485,0.526 2.367,0.498 10 Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 0.877,3.838 1.075,3.988 0.198,0.150 10 A8 0.234,1.552 0.570,1.702 0.336,0.150 10 E30 2.323,2.245 2.691,2.428 0.369,0.184 10 HSW 2.519,1.836 2.519,2.232 false

b.

for Hood Courtesy Switch Connector 4 Pin Type:

i.

Disconnect the E30 ECU connector.


ii.

Disconnect the A8 switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E30-24 (HSW) - A8-2 Always Below 1 Ω
A8-4 - Body ground Always Below 1 Ω
E30-24 (HSW) or A8-2 - Body ground Always 10 kΩ or higher





OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR