Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is operating, the certification ECU (smart key ECU assembly) outputs a signal continuously at 0.4 second intervals, causing the security horn to sound.

WIRING DIAGRAM

B184350E01
0.297,0.661 0.813,1.046 0.516,0.385 10 from Battery 1.333,0.883 2.115,1.072 0.783,0.189 10 SECURITY 2.608,1.445 3.391,1.635 0.783,0.189 10 SECURITY 5.542,0.734 5.873,0.905 0.332,0.171 10 SH- 5.264,0.851 5.480,0.999 0.216,0.148 10 20 5.332,1.583 5.610,1.743 0.278,0.159 10 E30 5.332,1.724 6.895,2.033 1.563,0.309 10 Certification ECU (Smart Key ECU Assembly) 3.856,1.944 4.244,2.155 0.387,0.211 10 A19 3.856,2.096 4.767,2.251 0.911,0.156 10 Security Horn 3.546,1.851 3.769,2.046 0.223,0.195 10 1 3.28,0.611 3.502,0.806 0.223,0.195 10 1 2.537,0.611 2.711,0.806 0.174,0.195 10 2 2.523,1.185 2.649,1.381 0.126,0.195 10 5 3.28,1.185 3.502,1.381 0.223,0.195 10 3

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY HORN)
a.

Operate the intelligent tester according to the steps on the display and select "Active Test".

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Security Horn Security horn ON/OFF -

OK:

Security horn operates normally.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.INSPECT FUSE (SECURITY)
2.INSPECT FUSE (SECURITY)
a.

Remove the SECURITY fuse from the No. 2 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
SECURITY fuse Always Below 1 Ω




OK

3.INSPECT SECURITY RELAY

NG

REPLACE FUSE

3.INSPECT SECURITY RELAY
a.
E145692E24
2.667,0.75 3.042,0.75 true 1.583,0.74 1.969,0.74 true 2.531,1.135 3.052,1.135 true 2.531,1.625 3.042,1.625 true 0.208,1.313 0.365,1.49 0.156,0.177 10 false 1 1.208,1.333 1.365,1.51 0.156,0.177 10 false 2 0.208,0.75 0.365,0.927 0.156,0.177 10 false 3 1.208,0.76 1.365,0.938 0.156,0.177 10 false 5 1.479,0.656 1.635,0.833 0.156,0.177 10 false 1 3.115,0.667 3.271,0.844 0.156,0.177 10 false 2 3.094,1.552 3.25,1.729 0.156,0.177 10 false 3 3.104,1.052 3.26,1.229 0.156,0.177 10 false 5

Remove the security relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

4.INSPECT SECURITY HORN ASSEMBLY

NG

REPLACE SECURITY RELAY

4.INSPECT SECURITY HORN ASSEMBLY
a.
E140469E01
2.273,1.236 2.196,0.643 2.196,0.643 2.007,0.643 false 1.869,0.565 1.970,0.721 0.100,0.156 10 1

Remove the security horn (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY HORN ASSEMBLY>REMOVAL).


b.

Apply battery voltage to the horn connector and check the operation of the horn.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Horn bracket
Horn sounds




OK

5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND SECURITY HORN)

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND SECURITY HORN)
U164008E02
5.708,1.771 5.708,2.125 true 4.677,0.083 7.042,0.604 2.365,0.521 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 4.667,2.302 7.021,2.646 2.354,0.344 10 false Front view of wire harness connector: (to Security Horn) 4.219,1.5 4.5,1.698 0.281,0.198 10 false E30 4.75,3.229 5.031,3.427 0.281,0.198 10 false A19 5.583,2.115 5.906,2.323 0.323,0.208 10 false SH- 0.448,0.125 2.802,0.49 2.354,0.365 10 false Front view of wire harness connector: (to Engine Room Relay Block) 2.604,2.708 3.521,2.896 0.917,0.188 10 false Security Relay

a.

Remove the SECURITY relay from the engine room relay block.


b.

Disconnect the E30 ECU connector.


c.

Disconnect the A19 horn connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay block security relay terminal 1 - E30-20 (SH-) Always Below 1 Ω
Relay block security relay terminal 3 - A19-1 Always Below 1 Ω
E30-20 (SH-) Body ground Always 10 kΩ or higher
A19-1 - Body ground Always 10 kΩ or higher



e.

Measure the voltage according to value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay block security relay terminal 2 - Body ground Always 11 to 14 V
Relay block security relay terminal 5 - Body ground Always 11 to 14 V




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR