Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Theft Warning Siren Circuit  


DESCRIPTION

The theft warning siren sounds if either of the following condition is met:

·

The theft deterrent system is in the alarm sounding state.

·

The theft warning siren is in the armed state when +B, GND or the communication line is open.


WIRING DIAGRAM

B311691E01
5.408,2.481 5.689,2.628 0.281,0.147 10 E30 5.436,0.949 5.565,1.096 0.128,0.147 10 7 3.271,0.949 3.399,1.096 0.128,0.147 10 4 2.27,0.434 2.398,0.581 0.128,0.147 10 5 2.27,1.899 2.398,2.047 0.128,0.147 10 2 3.699,1.899 3.827,2.047 0.128,0.147 10 3 3.662,1.404 3.755,1.552 0.093,0.147 10 * 0.257,3.359 3.422,3.506 3.166,0.147 10 *: for Hood Courtesy Switch Connector 4 Pin Type 5.208,1.404 5.301,1.552 0.093,0.147 10 * 5.009,1.899 5.137,2.047 0.128,0.147 10 1 5.626,1.033 6.066,1.180 0.441,0.147 10 SSCL 2.717,1.033 3.172,1.180 0.455,0.147 10 CONT 2.465,0.556 2.920,0.704 0.455,0.147 10 +B 3.895,1.909 4.260,2.056 0.364,0.147 10 SLF- 4.582,1.909 4.946,2.056 0.364,0.147 10 SLF+ 1.415,0.685 2.142,0.832 0.727,0.147 10 SECURITY 0.063,0.518 0.886,0.861 0.823,0.343 10 from Battery 2.508,2.039 2.963,2.187 0.455,0.147 10 GND 5.408,2.634 6.995,2.950 1.586,0.316 10 Certification ECU (Smart Key ECU Assembly) 2.063,2.355 2.344,2.502 0.281,0.147 10 K46 2.063,2.508 3.336,2.843 1.273,0.335 10 Theft Warning Siren Assembly 3.646,2.369 3.927,2.516 0.281,0.147 10 A8 3.646,2.522 5.084,2.699 1.438,0.178 10 Hood Lock Assembly*

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the theft warning siren assembly, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (THEFT WARNING SIREN)
a.

Operate the intelligent tester according to the steps on the display and select "Active Test".

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Security Horn2 Theft warning siren ON / OFF -

OK:

Siren operates normally.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - BATTERY AND BODY GROUND)
a.
U164236E01
0.067,0.057 0.256,0.205 0.189,0.148 10 *a 0.607,1.651 0.997,1.823 0.391,0.172 10 GND 2.525,1.651 2.742,1.823 0.217,0.172 10 +B 2.024,1.3 2.507,1.725 false 1.425,1.301 1.043,1.725 false 1.575,0.124 1.860,0.269 0.285,0.145 10 K46

Disconnect the K46 theft warning siren assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K46-5 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-2 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Theft Warning Siren Assembly)


OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - THEFT WARNING SIREN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - THEFT WARNING SIREN)
a.

Disconnect the E30 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K46 theft warning siren assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E30-7 (SSCL) - K46-4 (CONT) Always Below 1 Ω
E30-7 (SSCL) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK A
NG (except Hood Courtesy Switch Connector 4 Pin Type) B
NG (for Hood Courtesy Switch Connector 4 Pin Type) C



A

4.CHECK THEFT WARNING SIREN (OPERATION)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

5.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY AND THEFT WARNING SIREN)
4.CHECK THEFT WARNING SIREN (OPERATION)
a.

Temporarily replace the theft warning siren assembly with a new or known good one (refer to the Service Bulletin).


b.

Check that the theft warning siren operates normally.

OK:

Operates normally.




OK

END (THEFT WARNING SIREN ASSEMBLY IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY AND THEFT WARNING SIREN)
a.

Disconnect the E30 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A8 hood lock assembly connector.


c.

Disconnect the K46 theft warning siren assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A8-1 (SLF+) - E30-7 (SSCL) Always Below 1 Ω
A8-3 (SLF-) - K46-4 (CONT) Always Below 1 Ω
A8-1 (SLF+) - Body ground Always 10 kΩ or higher
A8-3 (SLF-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR