Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  B2762  Intrusion Sensor Signal Circuit Malfunction  


DESCRIPTION

The intrusion sensor (theft warning ultrasonic sensor) conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the IOUT line, the certification ECU (smart key ECU assembly) stores this DTC.


DTC Code DTC Detection Condition Trouble Area
B2762 After normal/trouble signal is output from intrusion sensor as result of self-diagnosis, following malfunctions are detected:
1.

IOUT line circuit is open

2.

Reception of signals other than normal/ trouble signal


·

Map light assembly

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

B187422E01
5.378,2.998 6.974,3.316 1.596,0.318 10 Certification ECU (Smart Key ECU Assembly) 1.932,3.163 3.209,3.346 1.276,0.184 10 Map Light Assembly 2.076,1.623 3.180,1.807 1.104,0.184 10 Intrusion Sensor 4.918,0.382 5.725,0.566 0.807,0.184 10 from Battery 5.628,1.65 5.826,1.834 0.199,0.185 10 +B 5.628,2.214 5.982,2.373 0.354,0.159 10 IOUT 3.475,2.145 3.830,2.297 0.355,0.152 10 IOUT 1.387,1.79 1.801,1.942 0.414,0.152 10 GND5 5.206,1.672 5.473,1.813 0.267,0.141 10 E29 5.293,1.493 5.388,1.637 0.095,0.144 10 1 5.206,2.241 5.473,2.385 0.267,0.143 10 E30 5.292,2.055 5.390,2.195 0.098,0.140 10 4 3.554,1.585 3.830,1.769 0.276,0.184 10 +B2 3.872,1.585 4.058,1.725 0.186,0.140 10 15 1.932,2.976 2.130,3.160 0.198,0.184 10 R7 1.2,1.79 1.300,1.930 0.099,0.140 10 3 3.732,0.382 4.539,0.566 0.807,0.184 10 from Battery 3.872,2.145 4.062,2.284 0.190,0.140 10 12

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT - BATTERY AND BODY GROUND)
a.
U166112E01
1.652,0.394 1.864,0.559 0.211,0.165 10 R7 0.098,0.053 0.310,0.218 0.211,0.165 10 *a 0.121,0.529 0.551,0.694 0.430,0.165 10 GND5 3.037,0.529 3.347,0.694 0.310,0.165 10 +B2 0.632,0.606 0.758,0.606 0.758,0.606 0.981,1.157 false 3.023,0.606 2.897,0.606 2.897,0.606 2.675,1.157 false

Disconnect the map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R7-15 (+B2) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R7-3 (GND5) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Map Light Assembly)


OK

2.CHECK INTRUSION SENSOR (IOUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK INTRUSION SENSOR (IOUT)
a.

Using an oscilloscope, check the waveform.

U164273E01
1.616,0.195 1.790,0.369 0.174,0.174 10 *a 3.428,0.23 3.692,0.404 0.264,0.174 10 R7 2.452,1.727 3.043,1.901 0.591,0.174 10 IOUT 1.254,2.547 1.845,2.721 0.591,0.174 10 HI 1.17,2.995 1.559,3.169 0.389,0.174 10 LOW 1.674,2.739 1.848,2.913 0.174,0.174 10 *b 2.445,2.883 2.619,3.057 0.174,0.174 10 *c 3.907,2.708 4.081,2.882 0.174,0.174 10 *d 3.907,3.182 4.081,3.356 0.174,0.174 10 *e 2.034,3.257 2.208,3.431 0.174,0.174 10 *f 2.445,3.266 2.619,3.440 0.174,0.174 10 *g 2.587,3.611 2.761,3.786 0.174,0.174 10 *h 1.445,4.172 1.620,4.346 0.174,0.174 10 *i 3.883,4.172 4.057,4.346 0.174,0.174 10 *j 3.164,1.071 2.839,1.784 false

Text in Illustration
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State

Measurement Condition
Tester Connection Content
Tester Connection R7-12 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor is normal, an initial response is output in response to the HI input from the certification ECU (smart key ECU assembly).

·

If the waveform output remains LO, there may be a problem with the certification ECU (smart key ECU assembly), as there is no input from the certification ECU (smart key ECU assembly).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).


Result
Result Proceed to
NG (Waveform output remains LO) A
NG (There is no initial response and the waveform output remains HI) B
OK (There is an initial response) C



A

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

B

C

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the R7 map light assembly connector.


b.

Disconnect the E30 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R7-12 (IOUT) - E30-4 (IOUT) Always Below 1 Ω
R7-12 (IOUT) or E30-4 (IOUT) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR