Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light is pressed, the sensor off signal is sent to the certification ECU (smart key ECU assembly) which causes the intrusion sensor to stop operating.


WIRING DIAGRAM

B128933E03
5.189,1.627 6.848,1.960 1.658,0.333 10 Certification ECU (Smart Key ECU Assembly) 5.068,0.678 5.266,0.847 0.198,0.170 10 5 5.349,0.775 5.838,0.959 0.489,0.184 10 SSW1 1.927,0.644 2.125,0.814 0.198,0.170 10 11 1.383,0.763 1.824,0.947 0.441,0.184 10 SOFF 1.003,1.463 1.214,1.616 0.211,0.153 10 R7 1.003,1.627 3.149,1.969 2.147,0.342 10 Map Light Assembly (Intrusion Sensor Cancel Switch) 5.208,1.463 5.487,1.604 0.279,0.141 10 E30

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTRUSION SENSOR CANCEL SWITCH)
a.

Using the intelligent tester, read the Data List.

Entry&Start
Tester Display Measurement Item / Display (Range) Normal Condition Diagnostic Note
Intrusion sensor OFF Intrusion sensor cancel switch /
ON or OFF
ON: Intrusion sensor active (switch off)
OFF: Intrusion sensor not active (switch on)
-

OK:

ON (intrusion sensor active [switch off]) appears on screen.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - MAP LIGHT ASSEMBLY)
U164115E02
1.25,1.906 0.594,1.646 true 2.01,3.875 2.708,3.615 true 0.177,0.115 2.531,0.656 2.354,0.542 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 0.167,2.563 2.521,2.865 2.354,0.302 10 false Front view of wire harness connector: (to Map Light) 0.281,3.99 0.5,4.146 0.219,0.156 10 false R7 0.198,2.021 0.469,2.177 0.271,0.156 10 false E30 0.104,1.563 0.521,1.719 0.417,0.156 10 false SSW1 2.75,3.531 3.156,3.688 0.406,0.156 10 false SOFF

a.

Disconnect the E30 ECU connector.


b.

Disconnect the R7 light connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E30-5 (SSW1) - R7-11 (SOFF) Always Below 1 Ω
E30-5 (SSW1) or R7-11 (SOFF) - Body ground Always 10 kΩ or higher




OK

3.CHECK MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH [OPERATION])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH [OPERATION])
a.

Temporarily replace the map light assembly (intrusion sensor cancel switch) with a new or normally functioning one (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).


b.

Turn the intrusion sensor off by pressing the intrusion sensor cancel switch. Check if the switch operates normally by checking that the theft deterrent system does not operate when you move your hand in front of the sensor.

OK:

Intrusion sensor cancel switch operates normally.




OK

END (MAP LIGHT [INTRUSION SENSOR CANCEL SWITCH] IS FAULTY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)