Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  B2764  Short to GND in Intrusion Sensor Signal Circuit  


DESCRIPTION

The intrusion sensor (theft warning ultrasonic sensor) conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the ISIF line, the certification ECU (smart key ECU assembly) stores this DTC.


DTC Code DTC Detection Condition Trouble Area
B2764 After normal/trouble signal is output from intrusion sensor as result of self-diagnosis, following malfunctions are detected:
1.

IOUT line circuit is shorted to ground

2.

Reception of signals other than normal/ trouble signal


·

Map light assembly

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

B187422E01
5.378,2.998 6.974,3.316 1.596,0.318 10 Certification ECU (Smart Key ECU Assembly) 1.932,3.163 3.209,3.346 1.276,0.184 10 Map Light Assembly 2.076,1.623 3.180,1.807 1.104,0.184 10 Intrusion Sensor 4.918,0.382 5.725,0.566 0.807,0.184 10 from Battery 5.628,1.65 5.826,1.834 0.199,0.185 10 +B 5.628,2.214 5.982,2.373 0.354,0.159 10 IOUT 3.475,2.145 3.830,2.297 0.355,0.152 10 IOUT 1.387,1.79 1.801,1.942 0.414,0.152 10 GND5 5.206,1.672 5.473,1.813 0.267,0.141 10 E29 5.293,1.493 5.388,1.637 0.095,0.144 10 1 5.206,2.241 5.473,2.385 0.267,0.143 10 E30 5.292,2.055 5.390,2.195 0.098,0.140 10 4 3.554,1.585 3.830,1.769 0.276,0.184 10 +B2 3.872,1.585 4.058,1.725 0.186,0.140 10 15 1.932,2.976 2.130,3.160 0.198,0.184 10 R7 1.2,1.79 1.300,1.930 0.099,0.140 10 3 3.732,0.382 4.539,0.566 0.807,0.184 10 from Battery 3.872,2.145 4.062,2.284 0.190,0.140 10 12

PROCEDURE

1.CHECK INTRUSION SENSOR (IOUT)
a.

Using an oscilloscope, check the waveform.

U164273E01
1.616,0.195 1.790,0.369 0.174,0.174 10 *a 3.428,0.23 3.692,0.404 0.264,0.174 10 R7 2.452,1.727 3.043,1.901 0.591,0.174 10 IOUT 1.254,2.547 1.845,2.721 0.591,0.174 10 HI 1.17,2.995 1.559,3.169 0.389,0.174 10 LOW 1.674,2.739 1.848,2.913 0.174,0.174 10 *b 2.445,2.883 2.619,3.057 0.174,0.174 10 *c 3.907,2.708 4.081,2.882 0.174,0.174 10 *d 3.907,3.182 4.081,3.356 0.174,0.174 10 *e 2.034,3.257 2.208,3.431 0.174,0.174 10 *f 2.445,3.266 2.619,3.440 0.174,0.174 10 *g 2.587,3.611 2.761,3.786 0.174,0.174 10 *h 1.445,4.172 1.620,4.346 0.174,0.174 10 *i 3.883,4.172 4.057,4.346 0.174,0.174 10 *j 3.164,1.071 2.839,1.784 false

Text in Illustration
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State

Measurement Condition
Tester Connection Content
Tester Connection R7-12 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor is normal, an initial response is output in response to the HI input from the certification ECU (smart key ECU assembly).

·

If the waveform output remains LO, there may be a problem with the certification ECU (smart key ECU assembly), as there is no input from the certification ECU (smart key ECU assembly).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).




OK

NG

2.CHECK INTRUSION SENSOR (IOUT)
2.CHECK INTRUSION SENSOR (IOUT)
a.
U166113E01
1.652,0.394 1.864,0.559 0.211,0.165 10 R7 0.098,0.053 0.310,0.218 0.211,0.165 10 *a 0.121,0.529 0.551,0.694 0.430,0.165 10 GND5 2.653,0.529 3.019,0.694 0.365,0.165 10 IOUT 0.632,0.606 0.758,0.606 0.758,0.606 0.981,1.157 false 2.639,0.606 2.513,0.606 2.513,0.606 2.291,1.157 false

Disconnect the map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
R7-12 (IOUT) - R7-3 (GND5) Immediately after theft deterrent system set


Result
Result Proceed to
IOUT voltage is below 1 V when theft deterrent system is set A
IOUT voltage is 6.5 V or higher when theft deterrent system is set B

HINT:

With connector R7 of the map light assembly disconnected, measure the voltage at IOUT when the theft deterrent system is set.




A

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

B

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the R7 map light assembly connector.


b.

Disconnect the E30 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R7-12 (IOUT) - E30-4 (IOUT) Always Below 1 Ω
R7-12 (IOUT) or E30-4 (IOUT) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR