Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A7  Open in Inside Luggage Compartment Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (inside luggage). For the No. 3 indoor electrical key antenna assembly (inside luggage) to detect when the electrical key transmitter sub-assembly is in the cabin, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A7 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A7 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

No. 3 indoor electrical key antenna assembly (inside luggage)

·

Harness or connector


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in luggage compartment:
·

Power source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A7 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B427596E22
5.302,0.76 5.75,0.906 0.448,0.146 10 false CLG7 1.219,0.771 1.708,0.958 0.49,0.188 10 false ANTE7 1.281,1.938 1.729,2.083 0.448,0.146 10 false CLGB 5.01,0.646 5.25,0.792 0.24,0.146 10 false 4 5.823,1.448 6.063,1.594 0.24,0.146 10 false IC 6.25,2 6.49,2.146 0.24,0.146 10 false E 5,1.667 5.302,1.813 0.302,0.146 10 false 3 6.5,1.813 6.802,1.958 0.302,0.146 10 false 11 0.406,2.542 0.979,2.688 0.573,0.146 10 false L63 0.385,2.729 2.656,3.073 2.271,0.344 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage) 1.771,0.76 1.896,0.906 0.125,0.146 10 false 1 1.76,1.938 1.885,2.083 0.125,0.146 10 false 2 5.104,2.625 6.708,3.104 1.604,0.479 10 false Certification ECU (Smart Key ECU Assembly) 4.906,0.875 5.385,1.021 0.479,0.146 10 false E129 4.917,2.021 5.396,2.229 0.479,0.208 10 false E129 6.448,2.021 6.927,2.167 0.479,0.146 10 false E130 5.292,1.896 5.74,2.042 0.448,0.146 10 false CG7B

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])
a.

Disconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the L63 No. 3 indoor electrical key antenna assembly (inside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E129-4 (CLG7) - L63-1 (ANTE7) Always Below 1 Ω
E129-3 (CG7B) - L63-2 (CLGB) Always Below 1 Ω
E130-11 (E) - Body ground Always Below 1 Ω
E129-4 (CLG7) or L63-1 (ANTE7) - Body ground Always 10 kΩ or higher
E129-3 (CG7B) or L63-2 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])
a.

Connect the E129 and E130 certification ECU (smart key ECU assembly) connectors.

U164320E02
3.958,1.26 3.917,2.146 true 6.031,1.385 6.365,2.208 true 4.083,1.271 4.646,2.198 true 0.167,0.063 0.385,0.26 0.219,0.198 10 false *a 0.74,2.646 0.958,2.844 0.219,0.198 10 false *b 1.5,4.375 1.719,4.573 0.219,0.198 10 false *c 2.354,4.396 2.573,4.594 0.219,0.198 10 false *d 0.729,3.688 1.094,3.854 0.365,0.167 10 false GND 6.344,2.219 6.479,2.385 0.135,0.167 10 false E 4.51,2.188 4.906,2.354 0.396,0.167 10 false CG7B 3.708,2.198 4.104,2.365 0.396,0.167 10 false CLG7 1.719,0.521 2.135,0.802 0.417,0.281 10 false E128 5.313,0.531 5.833,0.792 0.521,0.26 10 false E130 3.417,0.542 3.885,0.802 0.469,0.26 10 false E129

Text in Illustration
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform 1
*c For 30 seconds after closing any door using the door outside handle *d 30 seconds or more have elapsed after closing any door using the door outside handle


b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
E129-4 (CLG7) - E130-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)
E129-3 (CG7B) - E130-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)




OK

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage) with a new one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)