Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage compartment). For the electrical key antenna (outside luggage compartment) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A8 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Electrical key antenna (outside luggage compartment)

·

Harness or connector


Any time

*: Only output while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for back door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B427596E23
5.302,0.771 5.75,0.917 0.448,0.146 10 false CLG8 1.24,0.781 1.729,0.969 0.49,0.188 10 false ANTE8 1.271,1.917 1.719,2.063 0.448,0.146 10 false CLGB 5.031,0.677 5.271,0.823 0.24,0.146 10 false 2 5.875,1.25 6.115,1.396 0.24,0.146 10 false IC 6.281,2.052 6.521,2.198 0.24,0.146 10 false E 5.021,1.813 5.323,1.958 0.302,0.146 10 false 1 6.5,1.813 6.802,1.958 0.302,0.146 10 false 11 0.438,2.573 1.01,2.719 0.573,0.146 10 false K48 0.427,2.75 2.698,3.094 2.271,0.344 10 false Electrical Key Antenna (Outside Luggage Compartment) 1.771,1.927 1.896,2.073 0.125,0.146 10 false 1 1.771,0.76 1.896,0.906 0.125,0.146 10 false 2 5.083,2.646 6.688,3.125 1.604,0.479 10 false Certification ECU (Smart Key ECU Assembly) 4.927,0.865 5.406,1.01 0.479,0.146 10 false E129 4.917,2.01 5.396,2.219 0.479,0.208 10 false E129 6.469,2.031 6.948,2.177 0.479,0.146 10 false E130 5.292,1.917 5.74,2.063 0.448,0.146 10 false CG8B

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT])

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT])
a.

Disconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the K48 electrical key antenna (outside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E129-2 (CLG8) - K48-2 (ANTE8) Always Below 1 Ω
E129-1 (CG8B) - K48-1 (CLGB) Always Below 1 Ω
E130-11 (E) - Body ground Always Below 1 Ω
E129-2 (CLG8) or K48-2 (ANTE8) - Body ground Always 10 kΩ or higher
E129-1 (CG8B) or K48-1 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT])
U164321E02
4.135,1.25 2.99,2.135 true 6.031,1.365 6.354,2.177 true 4.25,1.26 4.375,2.104 true 0.229,0.083 0.448,0.281 0.219,0.198 10 false *a 0.469,2.458 0.688,2.656 0.219,0.198 10 false *b 0.75,3.677 1.115,3.844 0.365,0.167 10 false GND 6.333,2.219 6.469,2.385 0.135,0.167 10 false E 4.229,2.125 4.625,2.292 0.396,0.167 10 false CG8B 2.781,2.146 3.177,2.313 0.396,0.167 10 false CLG8 1.708,0.552 2.167,0.792 0.458,0.24 10 false E128 5.188,0.552 5.625,0.802 0.438,0.25 10 false E130 3.292,0.563 3.719,0.771 0.427,0.208 10 false E129

Text in Illustration
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform 1

a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
E129-2 (CLG8) - E130-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


5 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)
E129-1 (CG8B) - E130-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


5 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)




OK

4.REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)
a.

Temporarily replace the electrical key antenna (outside luggage compartment) with a new one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (ELECTRICAL KEY ANTENNA [OUTSIDE LUGGAGE COMPARTMENT] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)