Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


U164166E02
1.531,0.302 2,0.521 0.469,0.219 10 false E123

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E123-6 (AGND) - Body ground - LG - Body ground Transponder key amplifier ground Always Below 1 Ω -
E123-7 (TXCT) - E123-6 (AGND) Input G - LG Immobiliser communication input Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
E123-8 (CODE) - E123-6 (AGND) Output B - LG Immobiliser communication output Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
E123-10 (VC5) - E123-6 (AGND) Input BE - LG Transponder key amplifier power supply Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E123-7 (TXCT) - E123-6 (AGND) Input G - LG Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU [smart key ECU assembly] to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



E123-8 (CODE) - E123-6 (AGND) Output B - LG Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU [smart key ECU assembly])
Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
E123-10 (VC5) - E123-6 (AGND) Input BE - LG Transponder key amplifier power supply
(Power supplied from certification ECU [smart key ECU assembly] when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052E47
2.802,0.771 3.156,0.958 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection E123-7 (TXCT) - E123-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B345737E01
2.771,0.792 3.229,0.99 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection E123-8 (CODE) - E123-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection E123-10 (VC5) - E123-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U164303E02
1.708,0.479 2.156,0.729 0.448,0.25 10 false E128 3.375,0.49 3.823,0.74 0.448,0.25 10 false E129 5.094,0.49 5.542,0.74 0.448,0.25 10 false E130

a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E130-10 (+B) - E130-11 (E) Input P - BR +B power supply Engine switch of 11 to 14 V -
E130-11 (E) - Body ground - BR - Body ground Ground Always Below 1 Ω -


c.

Reconnect the E130 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E130-14 (TXCT) - E130-12 (AGND) Output G - LG Signal output to transponder key amplifier Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


E130-13 (CODE) - E130-12 (AGND) Input B - LG Signal input from transponder key amplifier Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
E130-15 (VC5) - E130-12 (AGND) Output BE - LG Transponder key amplifier power supply Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
E130-12 (AGND) - Body ground - LG - Body ground Transponder key amplifier ground Always Below 1 Ω
E130-19 (IND) - E130-11 (E) Output V - BR Security indicator output Engine switch off → on (IG) Pulse generation → Below 2 V -


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E130-14 (TXCT) - E130-12 (AGND) Output G - LG Signal output to transponder key amplifier
(Code sent from certification ECU [smart key ECU assembly] to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


E130-13 (CODE) - E130-12 (AGND) Input B - LG Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU [smart key ECU assembly])
Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
E130-15 (VC5) - E130-12 (AGND) Output BE - LG Transponder key amplifier power supply
(Power supplied from certification ECU [smart key ECU assembly] when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



f.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052E47
2.802,0.771 3.156,0.958 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection E130-14 (TXCT) - E130-12 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B345737E01
2.771,0.792 3.229,0.99 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection E130-13 (CODE) - E130-12 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection E130-15 (VC5) - E130-12 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK ID CODE BOX (IMMOBILISER CODE ECU)


U164247E02
1.563,0.469 2.083,0.792 0.521,0.323 10 false E124

a.

Disconnect the E124 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E124-1 (+B) - Body ground Input W - Body ground +B power supply Engine switch off 11 to 14 V B2789
E124-5 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω B2789


c.

Reconnect the E124 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E124-3 (EFII) - E124-5 (GND) Input W - BR EFI communication input
(Signal input from ECM to ID code box [immobiliser code ECU])
Engine switch off 11 to 14 V
·

B2799

·

B279A

·

EFI Code Receive

·

Engine Start Request


E124-4 (EFIO) - E124-5 (GND) Output P - BR EFI communication output (Signal output from ID code box [immobiliser code ECU] to ECM) Engine switch off 11 to 14 V
E124-3 (EFII) - E124-5 (GND) Input W - BR EFI communication input (Signal input from ECM to ID code box [immobiliser code ECU]) Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
E124-4 (EFIO) - E124-5 (GND) Output P - BR EFI communication output (Signal output from ID code box [immobiliser code ECU] to ECM) Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)


e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134E06
0.917,1.271 1.375,1.469 0.458,0.198 10 false GND 2.708,1.438 3.167,1.635 0.458,0.198 10 false *a 2.896,1.438 3.344,1.594 0.448,0.156 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection E124-3 (EFII) - E124-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259E01
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.338,1.59 3.533,1.763 0.195,0.173 10 *b 3.077,1.59 3.272,1.763 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection E124-4 (EFIO) - E124-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


U155868E03
1.573,0.24 1.875,0.406 0.302,0.167 10 false E26

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E26-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
E26-3 (IGE) - E26-1 (GND) Input W - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU [smart key ECU assembly]) Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Electrical key transmitter sub-assembly carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


E26-4 (SLP1) - E26-1 (GND) Output R - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked* 11 to 14 V → Below 1.5 V Sensor Value
E26-6 (IG2) - E26-1 (GND) Input P - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off → on (IG) Below 1 V → 11 to 14 V B2788
E26-7 (B) - Body ground Input G - Body ground Constant power supply Engine switch off 11 to 14 V B2788

HINT:

*: The steering locks when any door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594E01
3.008,0.035 3.194,0.193 0.186,0.158 10 *a 2.205,1.917 2.391,2.075 0.186,0.158 10 *b 2.918,1.56 3.302,1.719 0.384,0.158 10 GND 1.624,0.424 2.832,0.122 2.832,0.122 2.961,0.122 false 2.575,0.376 2.832,0.122 false 2.02,1.771 2.046,2.022 2.046,2.022 2.183,2.022 false

Waveform 1 (Reference)

Text in Illustration
*a Steering lock motor not operating
*b Steering lock motor operating

Measurement Condition
Item Content
Tester Connection E26-3 (IGE) - E26-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Electrical key transmitter sub-assembly carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off






CHECK ECM (FOR 3UR-FE)


U163443E02
5.5,0.26 5.771,0.417 0.271,0.156 10 false A38 2.26,0.26 2.531,0.417 0.271,0.156 10 false C45

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A38-3 (+B2) - C45-81 (E1) Input B - W-B Ignition power supply Engine switch on (IG) 11 to 14 V -
A38-2 (+B) - C45-81 (E1) Input B - W-B Ignition power supply Engine switch on (IG) 11 to 14 V -
A38-6 (MREL) - C45-81 (E1) Output V - W-B EFI-MAIN NO. 1 relay operation signal Engine switch on (IG) 11 to 14 V -
C45-41 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C45-81 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C45-43 (E02) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A38-1 (BATT) - C45-81 (E1) Input L - W-B +B power supply Always 11 to 14 V -
A38-48 (IMO) - C45-81 (E1) Output W - W-B ID code box (immobiliser code ECU) communication output Engine switch off Below 1 V -
A38-48 (IMO) - C45-81 (E1) Output W - W-B ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
A38-46 (IMI) - C45-81 (E1) Input P - W-B ID code box (immobiliser code ECU) communication input Engine switch off Below 1 V -
A38-46 (IMI) - C45-81 (E1) Input P - W-B ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134E01
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-48 (IMO) - C45-81 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259E01
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.338,1.59 3.533,1.763 0.195,0.173 10 *b 3.077,1.59 3.272,1.763 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-46 (IMI) - C45-81 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK ECM (FOR 1UR-FE, 1GR-FE)


U163444E02
5.406,0.156 5.677,0.313 0.271,0.156 10 false A38 5.781,0.146 6.052,0.302 0.271,0.156 10 false *1 2.156,0.448 2.427,0.604 0.271,0.156 10 false C46 2.531,0.49 2.802,0.646 0.271,0.156 10 false *2 1.042,2.354 2.208,2.552 1.167,0.198 10 false *1: for LHD 2.021,2.365 3.188,2.563 1.167,0.198 10 false *2: for RHD 2.146,0.156 2.417,0.313 0.271,0.156 10 false C45 2.521,0.125 2.792,0.281 0.271,0.156 10 false *1 5.406,0.448 5.677,0.604 0.271,0.156 10 false A52 5.792,0.479 6.063,0.635 0.271,0.156 10 false *2

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A38-2 (+B2) - C45-81 (E1) Input B - W-B Ignition power supply Engine switch on (IG) 11 to 14 V -
A38-3 (+B) - C45-81 (E1) Input B - W-B Ignition power supply Engine switch on (IG) 11 to 14 V -
A38-34 (MREL) - C45-81 (E1) Output V - W-B EFI-MAIN NO. 1 relay operation signal Engine switch on (IG) 11 to 14 V -
C45-43 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C45-81 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C45-42 (E02) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A38-1 (BATT) - C45-81 (E1) Input L - W-B +B power supply Always 11 to 14 V -
A38-29 (IMO) - C45-81 (E1) Output W - W-B ID code box (immobiliser code ECU) communication output Engine switch off Below 1 V -
A38-29 (IMO) - C45-81 (E1) Output W - W-B ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
A38-40 (IMI) - C45-81 (E1) Input P - W-B ID code box (immobiliser code ECU) communication input Engine switch off Below 1 V -
A38-40 (IMI) - C45-81 (E1) Input P - W-B ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

for RHD:
Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A52-2 (+B2) - C46-81 (E1) Input B - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A52-3 (+B) - C46-81 (E1) Input B - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A52-34 (MREL) - C46-81 (E1) Output V - BR EFI-MAIN NO. 1 relay operation signal Engine switch on (IG) 11 to 14 V -
C46-43 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C46-81 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C46-42 (E02) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A52-1 (BATT) - C46-81 (E1) Input L - BR +B power supply Always 11 to 14 V -
A52-29 (IMO) - C46-81 (E1) Output W - BR ID code box (immobiliser code ECU) communication output Engine switch off Below 1 V -
A52-29 (IMO) - C46-81 (E1) Output W - BR ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
A52-40 (IMI) - C46-81 (E1) Input P - BR ID code box (immobiliser code ECU) communication input Engine switch off Below 1 V -
A52-40 (IMI) - C46-81 (E1) Input P - BR ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134E01
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-29 (IMO) - C45-81 (E1)*1
A52-29 (IMO) - C46-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

*1: for LHD

*2: for RHD



ii.

Waveform 2 (Reference)

B333259E01
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.338,1.59 3.533,1.763 0.195,0.173 10 *b 3.077,1.59 3.272,1.763 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-40 (IMI) - C45-81 (E1)*1
A52-40 (IMI) - C46-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

*1: for LHD

*2: for RHD





CHECK ECM (FOR 1VD-FTV)


U163444E03
5.417,0.146 5.688,0.302 0.271,0.156 10 false A38 5.76,0.135 6.031,0.292 0.271,0.156 10 false *1 2.146,0.438 2.417,0.594 0.271,0.156 10 false C46 2.531,0.448 2.802,0.604 0.271,0.156 10 false *2 1.042,2.344 2.208,2.542 1.167,0.198 10 false *1: for LHD 2.031,2.354 3.198,2.552 1.167,0.198 10 false *2: for RHD 2.167,0.135 2.438,0.292 0.271,0.156 10 false C45 2.5,0.135 2.771,0.292 0.271,0.156 10 false *1 5.417,0.448 5.688,0.604 0.271,0.156 10 false A52 5.792,0.458 6.063,0.615 0.271,0.156 10 false *2

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A38-1 (+B2) - C45-81 (E1) Input B - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A38-2 (+B) - C45-81 (E1) Input B - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A38-44 (MREL) - C45-81 (E1) Output V - BR EFI-MAIN NO. 1 relay operation signal Engine switch on (IG) 11 to 14 V -
C45-22 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C45-81 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C45-21 (E02) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A38-20 (BATT) - C45-81 (E1) Input L - BR +B power supply Always 11 to 14 V -
A38-10 (IMO) - C45-81 (E1) Output W - BR ID code box (immobiliser code ECU) communication output Engine switch off Below 1 V -
A38-10 (IMO) - C45-81 (E1) Output W - BR ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
A38-11 (IMI) - C45-81 (E1) Input P - BR ID code box (immobiliser code ECU) communication input Engine switch off Below 1 V -
A38-11 (IMI) - C45-81 (E1) Input P - BR ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

for RHD:
Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A52-1 (+B2) - C46-81 (E1) Input B - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A52-2 (+B) - C46-81 (E1) Input B - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A52-44 (MREL) - C46-81 (E1) Output V - BR EFI-MAIN NO. 1 relay operation signal Engine switch on (IG) 11 to 14 V -
C46-22 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C46-81 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C46-21 (E02) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A52-20 (BATT) - C46-81 (E1) Input L - BR +B power supply Always 11 to 14 V -
A52-10 (IMO) - C46-81 (E1) Output W - BR ID code box (immobiliser code ECU) communication output Engine switch off Below 1 V -
A52-10 (IMO) - C46-81 (E1) Output W - BR ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
A52-11 (IMI) - C46-81 (E1) Input P - BR ID code box (immobiliser code ECU) communication input Engine switch off Below 1 V -
A52-11 (IMI) - C46-81 (E1) Input P - BR ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134E01
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-10 (IMO) - C45-81 (E1)*1
A52-10 (IMO) - C46-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

*1: for LHD

*2: for RHD



ii.

Waveform 2 (Reference)

B333259E01
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.338,1.59 3.533,1.763 0.195,0.173 10 *b 3.077,1.59 3.272,1.763 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-11 (IMI) - C45-81 (E1)*1
A52-11 (IMI) - C46-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

*1: for LHD

*2: for RHD