Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC Code DTC Detection Condition Trouble Area
B2784 The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU [smart key ECU assembly]). (1 trip detection logic*)
·

Terminal AGND, VC5, TXCT or CODE circuit is open (includes disconnection of the engine switch).

·

The transponder key amplifier coil built into the engine switch is open.


·

Engine switch

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when transmitter battery is depleted by holding transmitter near engine switch and pressing and holding engine switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B2784 -

WIRING DIAGRAM

E305785E29
1.563,0.813 2.083,1.271 0.521,0.458 10 false VC5 1.917,0.698 2.438,1.156 0.521,0.458 10 false 10 1.479,1.323 2,1.781 0.521,0.458 10 false TXCT 1.469,1.729 1.99,2.188 0.521,0.458 10 false CODE 1.938,1.219 2.458,1.677 0.521,0.458 10 false 7 1.938,1.729 2.458,2.188 0.521,0.458 10 false 8 1.938,2.24 2.458,2.698 0.521,0.458 10 false 6 1.469,2.24 1.99,2.698 0.521,0.458 10 false AGND 0.51,3.063 0.854,3.24 0.344,0.177 10 false E123 0.51,3.219 1.948,3.427 1.438,0.208 10 false Engine Switch 5,0.698 5.521,1.156 0.521,0.458 10 false 15 5.01,1.219 5.531,1.677 0.521,0.458 10 false 14 5.01,1.74 5.531,2.198 0.521,0.458 10 false 13 5.01,2.25 5.531,2.708 0.521,0.458 10 false 12 5.719,0.313 6.24,0.771 0.521,0.458 10 false 5 V 5.271,3.021 5.792,3.479 0.521,0.458 10 false E130 5.281,3.188 6.823,3.792 1.542,0.604 10 false Certification ECU (Smart Key ECU Assembly) 5.26,0.708 5.781,1.167 0.521,0.458 10 false VC5 5.26,1.208 5.781,1.667 0.521,0.458 10 false TXCT 5.25,1.74 5.771,2.198 0.521,0.458 10 false CODE 5.25,2.25 5.771,2.708 0.521,0.458 10 false AGND 6.156,1.542 6.677,2 0.521,0.458 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ENGINE SWITCH)
a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the E123 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-15 (VC5) - E123-10 (VC5) Always Below 1 Ω
E130-14 (TXCT) - E123-7 (TXCT) Always Below 1 Ω
E130-13 (CODE) - E123-8 (CODE) Always Below 1 Ω
E130-12 (AGND) - E123-6 (AGND) Always Below 1 Ω
E130-15 (VC5) or E123-10 (VC5) - Body ground Always 10 kΩ or higher
E130-14 (TXCT) or E123-7 (TXCT) - Body ground Always 10 kΩ or higher
E130-13 (CODE) or E123-8 (CODE) - Body ground Always 10 kΩ or higher
E130-12 (AGND) or E123-6 (AGND) - Body ground Always 10 kΩ or higher




OK

2.REPLACE ENGINE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE ENGINE SWITCH

NEXT

3.CLEAR DTC
4.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.




OK

END (ENGINE SWITCH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)