Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ignition Switch Engine switch on (IG) signal / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
#Codes Number of trouble codes / Min: 0, Max: 255 - -
Immobiliser Engine immobiliser system status / Set or Unset Set: Key not in cabin
Unset: Key in cabin
-
Master Key Indicates whether the master key ID code matches the ID code registered in the certification ECU (smart key ECU assembly) when a start-up operation is performed due to depletion of master key battery / Match or No Match Match: When a start-up operation is performed due to the depletion of the master key battery
No Match: When a start-up operation is not preformed due to the depletion of the master key battery or when the negative (-) battery terminal is disconnected
When this item displays as "Match", it continues to display as "Match" until the negative (-) battery terminal is disconnected
HINT:

Make sure to remove the master key battery in order to prevent misdiagnosis when checking operation


BCC Malfunction Transponder chip signal / OK or NG OK: Correct data sent
NG: Incorrect data sent
-
Abnormal Status Transponder chip data / OK or NG OK: Data OK
NG: Data error
-
Different Encrypt Code Transponder chip signal / OK or NG OK: Correct data sent
NG: Incorrect data sent
-
Different Serial Number Transponder chip signal / OK or NG OK: Correct data sent
NG: Incorrect data sent
-
Frame Error Transponder chip signal / OK or NG OK: Correct data sent
NG: Incorrect data sent
-
Response Transponder chip signal / OK or NG OK: Correct data sent
NG: Incorrect data sent
-
ID-BOX Sleep Condition ID code box condition / Yes or No Yes: ID code box in sleep condition
No: ID code box not in sleep condition
-
ID-BOX Start Condition ID code box condition / Yes or No Yes: ID code box sends wake up signal
No: ID code box does not send wake up signal
-
Engine Start Request ID code box start request condition / OK or NG OK: Start request condition signal received (past)
NG: Start request condition signal not received (past)
-
S Code Check S code verification result / OK or NG OK: Verification confirmed
NG: Verification not confirmed
-
L Code Check L code verification result / OK or NG OK: Verification confirmed
NG: Verification not confirmed
-
Unlock Request Receive Steering unlock command reception status / OK or NG OK: Steering unlock request received
NG: Steering unlock request not received
-
Lock Request Receive Steering lock command reception status / OK or NG OK: Steering lock request received
NG: Steering lock request is not received
-
S Code Check (Past) S code verification result (past) / OK or NG OK: Verification confirmed (past)
NG: Verification not confirmed (past)
-
L Code Check (Past) L code verification result (past) / OK or NG OK: Verification confirmed (past)
NG: Verification not confirmed (past)
-
EFI Code Receive SFI*1 or ECD*2 code receive (when DTC stored) / OK or NG OK: SFI*1 or ECD*2 code received
NG: SFI*1 or ECD*2 code not received
-
EFI communication SFI*1 or ECD*2 communication / OK or NG OK: SFI*1 or ECD*2 communication normal
NG: SFI*1 or ECD*2 communication abnormal
-

HINT:
·

*1: for 1GR-FE, 1UR-FE, 3UR-FE

·

*2: for 1VD-FTV





PERFORM ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON or OFF -