Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC Code DTC Detection Condition Trouble Area
B278A A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) detected. (1 trip detection logic)*
·

Engine switch

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when transmitter battery is depleted by holding transmitter near engine switch and pressing and holding engine switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B278A -

WIRING DIAGRAM

E305785E30
1.521,0.813 2.042,1.271 0.521,0.458 10 false VC5 1.917,0.698 2.438,1.156 0.521,0.458 10 false 10 1.458,1.323 1.979,1.781 0.521,0.458 10 false TXCT 1.396,1.729 1.917,2.188 0.521,0.458 10 false CODE 1.938,1.219 2.458,1.677 0.521,0.458 10 false 7 1.938,1.729 2.458,2.188 0.521,0.458 10 false 8 1.938,2.24 2.458,2.698 0.521,0.458 10 false 6 1.396,2.24 1.917,2.698 0.521,0.458 10 false AGND 0.479,3.063 0.823,3.24 0.344,0.177 10 false E123 0.479,3.219 1.917,3.427 1.438,0.208 10 false Engine Switch 5,0.698 5.521,1.156 0.521,0.458 10 false 15 5.01,1.219 5.531,1.677 0.521,0.458 10 false 14 5.01,1.74 5.531,2.198 0.521,0.458 10 false 13 5.01,2.25 5.531,2.708 0.521,0.458 10 false 12 5.719,0.313 6.24,0.771 0.521,0.458 10 false 5 V 5.146,3.042 5.667,3.5 0.521,0.458 10 false E130 5.135,3.198 6.969,3.667 1.833,0.469 10 false Certification ECU (Smart Key ECU Assembly) 5.26,0.708 5.781,1.167 0.521,0.458 10 false VC5 5.26,1.208 5.781,1.667 0.521,0.458 10 false TXCT 5.25,1.74 5.771,2.198 0.521,0.458 10 false CODE 5.25,2.25 5.771,2.708 0.521,0.458 10 false AGND 6.156,1.542 6.677,2 0.521,0.458 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Using an oscilloscope, check the waveform.

U164338E02
2.333,1.635 2.333,2.406 2.333,2.406 2.438,2.406 true 1.875,1.646 1.875,2.417 1.875,2.417 1.771,2.417 true 1.094,0.365 1.604,0.729 0.51,0.365 10 false *a 1.938,0.458 2.448,0.823 0.51,0.365 10 false E123 2.49,2.333 3,2.698 0.51,0.365 10 false AGND 6.49,1.375 7,1.74 0.51,0.365 10 false GND 1.469,2.344 1.979,2.708 0.51,0.365 10 false VC5

Text in Illustration
*a Component with harness connected
(Engine Switch)
- -

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
E123-10 (VC5) - E123-6 (AGND) Engine switch off, key not in cabin, within 30 seconds after engine switch pressed 2 V/DIV., 200 ms./DIV. Pulse generation


OK:

The waveform is similar to that shown in the illustration.


Result:
Result Proceed to
OK (for 3UR-FE) A
OK (for 1UR-FE) B
OK (for 1GR-FE) C
OK (for 1VD-FTV) D
NG E




A

B

C

D

E

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ENGINE SWITCH)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ENGINE SWITCH)
a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the E123 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-15 (VC5) - E123-10 (VC5) Always Below 1 Ω
E130-12 (AGND) - E123-6 (AGND) Always Below 1 Ω
E130-15 (VC5) or E123-23 (VC5) - Body ground Always 10 kΩ or higher
E130-12 (AGND) or E123-6 (AGND) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the E130 certification ECU (smart key ECU assembly) connector.

U164316E01
6.658,2.039 7.080,2.197 0.422,0.158 10 AGND 4.445,1.85 4.832,2.008 0.387,0.158 10 VC5 0.21,0.07 0.396,0.229 0.186,0.158 10 *a 5.195,0.238 5.743,0.491 0.548,0.253 10 E130 5.947,1.082 6.413,2.105 6.413,2.105 6.62,2.105 false 5.538,1.082 4.918,1.94 4.918,1.94 4.795,1.94 false 5.947,1.082 6.413,2.105 6.413,2.105 6.62,2.105 false 5.538,1.082 4.918,1.94 4.918,1.94 4.795,1.94 false

Text in Illustration
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
- -


b.

Reconnect the E123 engine switch connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E130-15 (VC5) - E130-12 (AGND) Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V



Result
Result Proceed to
OK (for 3UR-FE) A
OK (for 1UR-FE) B
OK (for 1GR-FE) C
OK (for 1VD-FTV) D
NG E


A

B

C

D

E

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)