Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM stores this DTC.

DTC Code DTC Detection Condition Trouble Area
B279A The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).
·

ID code box (immobiliser code ECU)

·

ECM

·

Harness or connector



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started Engine cannot be started

Related Data List and Active Test
DTC Code Data List and Active Test
B279A -

WIRING DIAGRAM

E305787E12
2.219,1.042 3.344,1.24 1.125,0.198 10 false 46*3, 40*4, 11*5 1.896,1.052 2.573,1.469 0.677,0.417 10 false IMI 0.885,2.063 1.875,2.313 0.99,0.25 10 false A38*1, A52*2 1.115,2.24 1.583,2.594 0.469,0.354 10 false ECM 5.073,2.052 5.75,2.469 0.677,0.417 10 false E124 5.073,2.219 6.677,2.719 1.604,0.5 10 false ID Code Box (Immobiliser Code ECU) 5.115,1.063 5.792,1.479 0.677,0.417 10 false EFIO 4.854,1.063 5.531,1.479 0.677,0.417 10 false 4 2.885,1.531 4.25,1.729 1.365,0.198 10 false *1: for LHD 2.885,1.781 4.25,1.979 1.365,0.198 10 false *2: for RHD 2.885,2.031 4.25,2.229 1.365,0.198 10 false *3: for 3UR-FE 2.885,2.271 4.5,2.521 1.615,0.25 10 false *4: for 1UR-FE, 1GR-FE 2.885,2.51 4.5,2.76 1.615,0.25 10 false *5: for 1VD-FTV

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ECM or ID code box (immobiliser code ECU), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

2.CHECK FOR DTC
a.

Turn the engine switch on (IG) and wait 10 seconds.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B279A is output A
DTC B279A and other DTCs are output B

HINT:

If DTCs other than DTC B279A are output, troubleshoot those DTCs first.




A

3.CHECK CONNECTION OF CONNECTOR

B

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM)
a.

Disconnect the E124 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

·

*1: for LHD

·

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3UR-FE:
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-46 (IMI) Always Below 1 Ω
E124-4 (EFIO) or A38-46 (IMI) - Body ground Always 10 kΩ or higher

for 1UR-FE, 1GR-FE (for LHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-40 (IMI) Always Below 1 Ω
E124-4 (EFIO) or A38-40 (IMI) - Body ground Always 10 kΩ or higher

for 1UR-FE, 1GR-FE (for RHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A52-40 (IMI) Always Below 1 Ω
E124-4 (EFIO) or A52-40 (IMI) - Body ground Always 10 kΩ or higher

for 1VD-FTV (for LHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-11 (IMI) Always Below 1 Ω
E124-4 (EFIO) or A38-11 (IMI) - Body ground Always 10 kΩ or higher

for 1VD-FTV (for RHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A52-11 (IMI) Always Below 1 Ω
E124-4 (EFIO) or A52-11 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 3UR-FE:
Tester Connection Condition Specified Condition
A38-46 (IMI) - Body ground Always 11 to 14 V

for 1UR-FE, 1GR-FE (for LHD):
Tester Connection Condition Specified Condition
A38-40 (IMI) - Body ground Always 11 to 14 V

for 1UR-FE, 1GR-FE (for RHD):
Tester Connection Condition Specified Condition
A52-40 (IMI) - Body ground Always 11 to 14 V

for 1VD-FTV (for LHD):
Tester Connection Condition Specified Condition
A38-11 (IMI) - Body ground Always 11 to 14 V

for 1VD-FTV (for RHD):
Tester Connection Condition Specified Condition
A52-11 (IMI) - Body ground Always 11 to 14 V




OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.




NEXT

6.REGISTER RECOGNITION CODES
6.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.




NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

8.CLEAR DTC
9.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR).

OK:

DTC B279A is not output.

Result Proceed to
OK A
NG (for 3UR-FE) B
NG (for 1UR-FE) C
NG (for 1GR-FE) D
NG (for 1VD-FTV) E




A

END (ID CODE BOX [IMMOBILISER CODE ECU] WAS DEFECTIVE)

B

C

D

E