Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B2799  Immobiliser Malfunction  


DESCRIPTION

When there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.

DTC Code DTC Detection Condition Trouble Area
B2799 Either condition is met (1 trip detection logic*):
·

A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU).


·

ID code box (immobiliser code ECU)

·

ECM

·

Harness or connector



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

E305786E12
4.365,1.146 5.802,1.51 1.438,0.365 10 false 48*3, 29*4, 10*5 4.354,2.052 5.74,2.375 1.385,0.323 10 false 46*3, 40*4, 11*5 2.156,1.125 2.729,1.5 0.573,0.375 10 false 3 2.167,2.031 2.74,2.406 0.573,0.375 10 false 4 1.781,1.125 2.354,1.5 0.573,0.375 10 false EFII 1.698,2.031 2.271,2.406 0.573,0.375 10 false EFIO 5.479,1.135 6.063,1.521 0.583,0.385 10 false IMO 5.49,2.031 6.063,2.406 0.573,0.375 10 false IMI 1.333,0.479 1.906,0.854 0.573,0.375 10 false 12 V 0.5,3.052 1.073,3.427 0.573,0.375 10 false E124 0.51,3.208 2.104,3.625 1.594,0.417 10 false ID Code Box (Immobiliser Code ECU) 5.729,3.094 6.75,3.375 1.021,0.281 10 false A38*1, A52*2 5.979,3.26 6.906,3.698 0.927,0.438 10 false ECM 5.635,1.719 6.208,2.094 0.573,0.375 10 false 12 V 3.083,2.5 3.781,2.781 0.698,0.281 10 false *1: for LHD 3.083,2.75 3.781,3.031 0.698,0.281 10 false *2: for RHD 3.083,3.01 4.052,3.302 0.969,0.292 10 false *3: for 3UR-FE 3.083,3.271 4.656,3.5 1.573,0.229 10 false *4: for 1UR-FE, 1GR-FE 3.094,3.531 4.667,3.76 1.573,0.229 10 false *5: for 1VD-FTV

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ECM or ID code box (immobiliser code ECU), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B2799 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

2.CLEAR DTC
3.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.




OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM)
4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM)
a.

Disconnect the E124 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

·

*1: for LHD

·

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3UR-FE:
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-46 (IMI) Always Below 1 Ω
E124-3 (EFII) - A38-48 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A38-46 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A38-48 (IMO) - Body ground Always 10 kΩ or higher

for 1UR-FE, 1GR-FE (for LHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-40 (IMI) Always Below 1 Ω
E124-3 (EFII) - A38-29 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A38-40 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A38-29 (IMO) - Body ground Always 10 kΩ or higher

for 1UR-FE, 1GR-FE (for RHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A52-40 (IMI) Always Below 1 Ω
E124-3 (EFII) - A52-29 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A52-40 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A52-29 (IMO) - Body ground Always 10 kΩ or higher

for 1VD-FTV (for LHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A38-11 (IMI) Always Below 1 Ω
E124-3 (EFII) - A38-10 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A38-11 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A38-10 (IMO) - Body ground Always 10 kΩ or higher

for 1VD-FTV (for RHD):
Tester Connection Condition Specified Condition
E124-4 (EFIO) - A52-11 (IMI) Always Below 1 Ω
E124-3 (EFII) - A52-10 (IMO) Always Below 1 Ω
E124-4 (EFIO) or A52-11 (IMI) - Body ground Always 10 kΩ or higher
E124-3 (EFII) or A52-10 (IMO) - Body ground Always 10 kΩ or higher




OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.




NEXT

6.REGISTER RECOGNITION CODE
6.REGISTER RECOGNITION CODE
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.




NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

8.CLEAR DTC
9.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR).

OK:

DTC B2799 is not output.

Result Proceed to
OK A
NG (for 3UR-FE) B
NG (for 1UR-FE) C
NG (for 1GR-FE) D
NG (for 1GVD-FTV) E




A

END (ID CODE BOX [IMMOBILISER CODE ECU] WAS DEFECTIVE)

B

C

D

E