Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


U164167E02
3.385,0.656 3.708,0.813 0.323,0.156 10 false E96

a.

Disconnect the E96 transponder key ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
E96-1 (+B) - E96-5 (GND) Input W - BR Battery Always 11 to 14 V +B
E96-2 (IG) - E96-5 (GND) Input P - BR Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
E96-3 (KSW) - E96-5 (GND) Input G - BR Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key in ignition key cylinder Below 1 Ω
E96-5 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω -
E96-7 (CTY) - Body ground*1 Input V - Body ground Door courtesy switch LH signal Driver side door closed 10 kΩ or higher -
Driver side door open Below 1 Ω

·

*: for LHD



c.

Reconnect the E96 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
E96-8 (IND) - E96-5 (GND) Output V - BR Security indicator signal No key in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Key in ignition key cylinder (immobiliser system unset) Below 1 V
E96-9 (D) - E96-5 (GND) Input/Output R - BR DLC3 communication Without communication Below 1 V -
During communication Pulse generation
E96-4 (ANT1) - E96-5 (GND) Input/Output R - BR Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
E96-15 (ANT2) - E96-5 (GND) Input/Output L - BR Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
E96-12 (EFII) - E96-5 (GND) Output W - BR ECM input signal Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
-
E96-13 (EFIO) - E96-5 (GND) Input P - BR ECM output signal Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909E01
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Tester Connection E96-4 (ANT1) - E96-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910E01
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Tester Connection E96-15 (ANT2) - E96-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134E02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection E96-12 (EFII) - E96-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B333259E02
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.31,1.366 3.505,1.539 0.195,0.173 10 *b 3.119,1.352 3.314,1.525 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection E96-13 (EFIO) - E96-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




CHECK ECM (for 1GR-FE)


U163442E01
5.577,0.42 5.851,0.576 0.274,0.156 10 A52 2.467,0.42 2.741,0.576 0.274,0.156 10 C46 5.577,0.077 5.851,0.233 0.274,0.156 10 A38 2.467,0.077 2.741,0.233 0.274,0.156 10 C45 2.873,0.077 3.067,0.233 0.194,0.156 10 *1 0.26,2.487 1.084,2.643 0.824,0.156 10 *1: for LHD 1.344,2.487 2.124,2.643 0.780,0.156 10 *2: for RHD 2.873,0.42 3.067,0.576 0.194,0.156 10 *2 5.949,0.077 6.143,0.233 0.194,0.156 10 *1 5.949,0.42 6.143,0.576 0.194,0.156 10 *2

a.

for LHD:

i.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C45-81 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A38-1 (BATT) - C45-81 (E1) Input L - BR +B power supply Always 11 to 14 V -
A38-2 (+B2) - C45-81 (E1) Input B - BR +B power supply Ignition switch ON 11 to 14 V -
A38-3 (+B) - C45-81 (E1) Input B - BR +B power supply Ignition switch ON 11 to 14 V -
A38-29 (IMO) - C45-81 (E1) Input W - BR Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication input Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected. Pulse generation
(See waveform 1)
-
A38-40 (IMI) - C45-81 (E1) Output P - BR Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication output Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected. Pulse generation
(See waveform 2)
-



b.

for RHD:

i.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C46-81 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A52-1 (BATT) - C46-81 (E1) Input L - BR +B power supply Always 11 to 14 V -
A52-2 (+B2) - C46-81 (E1) Input B - BR +B power supply Ignition switch ON 11 to 14 V -
A52-3 (+B) - C46-81 (E1) Input B - BR +B power supply Ignition switch ON 11 to 14 V -
A52-29 (IMO) - C46-81 (E1) Input W - BR Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication input Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected. Pulse generation
(See waveform 1)
-
A52-40 (IMI) - C46-81 (E1) Output P - BR Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication output Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected. Pulse generation
(See waveform 2)
-



c.

Inspect using an oscilloscope.

i.

Waveform 1 (Reference)

B325134E02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-29 (IMO) - C45-81 (E1)*1
A52-29 (IMO) - C46-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected

*1: for LHD

*2: for RHD



ii.

Waveform 2 (Reference)

B333259E02
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.31,1.366 3.505,1.539 0.195,0.173 10 *b 3.119,1.352 3.314,1.525 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-40 (IMI) - C45-81 (E1)*1
A52-40 (IMI) - C46-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected

*1: for LHD

*2: for RHD



iii.



CHECK ECM (for 1VD-FTV)


U163442E01
5.577,0.42 5.851,0.576 0.274,0.156 10 A52 2.467,0.42 2.741,0.576 0.274,0.156 10 C46 5.577,0.077 5.851,0.233 0.274,0.156 10 A38 2.467,0.077 2.741,0.233 0.274,0.156 10 C45 2.873,0.077 3.067,0.233 0.194,0.156 10 *1 0.26,2.487 1.084,2.643 0.824,0.156 10 *1: for LHD 1.344,2.487 2.124,2.643 0.780,0.156 10 *2: for RHD 2.873,0.42 3.067,0.576 0.194,0.156 10 *2 5.949,0.077 6.143,0.233 0.194,0.156 10 *1 5.949,0.42 6.143,0.576 0.194,0.156 10 *2

a.

for LHD:

i.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C45-81 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A38-1 (BATT) - C45-81 (E1) Input L - BR +B power supply Always 11 to 14 V -
A38-3 (+B) - C45-81 (E1) Input B - BR +B power supply Ignition switch ON 11 to 14 V -
A38-29 (IMO) - C45-81 (E1) Input W - BR Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication input Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected. Pulse generation
(See waveform 1)
-
A38-40 (IMI) - C45-81 (E1) Output P - BR Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication output Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected. Pulse generation
(See waveform 2)
-



b.

for RHD:

i.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C46-81 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A52-1 (BATT) - C46-81 (E1) Input L - BR +B power supply Always 11 to 14 V -
A52-3 (+B) - C46-81 (E1) Input B - BR +B power supply Ignition switch ON 11 to 14 V -
A52-29 (IMO) - C46-81 (E1) Input W - BR Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication input Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected. Pulse generation
(See waveform 1)
-
A52-40 (IMI) - C46-81 (E1) Output P - BR Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication output Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected. Pulse generation
(See waveform 2)
-



c.

Inspect using an oscilloscope.

i.

Waveform 1 (Reference)

B325134E02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-29 (IMO) - C45-81 (E1)*1
A52-29 (IMO) - C46-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected

*1: for LHD

*2: for RHD



ii.

Waveform 2 (Reference)

B333259E02
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.31,1.366 3.505,1.539 0.195,0.173 10 *b 3.119,1.352 3.314,1.525 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection A38-40 (IMI) - C45-81 (E1)*1
A52-40 (IMI) - C46-81 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected

*1: for LHD

*2: for RHD