Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B2795  Unmatched Key Code  


DESCRIPTION

This DTC is stored when a key with a different vehicle serial number is inserted into the ignition key cylinder.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2795 A key with a different vehicle serial number is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Transponder key ECU assembly


Insert the key into the ignition key cylinder.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation When Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2795 Different Serial Number

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the key or transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

2.CHECK FOR DTC
a.

Insert and remove each registered key one at a time, and check for DTCs each time (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:
·

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

·

If DTC B2795 is output, check for DTCs with the next key after clearing the DTCs.



OK:

DTC B2795 is not output.


Result
Result Proceed to
OK A
NG (any key) B
NG (all keys) C



A

B

3.CHECK IGNITION SWITCH (OPERATION)

C

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
3.CHECK IGNITION SWITCH (OPERATION)
a.

Check that the ignition switch can be turned to ON using the key for which the DTC was stored.

OK:

Ignition switch can be turned to ON using the key for which the DTC was stored.




OK

4.REREGISTER MALFUNCTIONING KEY

NG

REPLACE KEY THAT CANNOT START ENGINE

4.REREGISTER MALFUNCTIONING KEY

b.

Reregister the key code with the transponder key ECU assembly (refer to the Service Bulletin).

OK:

Registration procedure can be completed.




OK

END (KEY CODE WAS NOT REGISTERED NORMALLY)

NG

REPLACE KEY THAT CANNOT START ENGINE

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly (refer to the Service Bulletin).



NEXT

6.REGISTER KEY
6.REGISTER KEY
a.

Reregister the key (refer to the Service Bulletin).



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (refer to the Service Bulletin).



NEXT

8.CLEAR DTC
9.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:
·

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

·

If DTC B2795 is output, check for DTCs with the next key after clearing the DTCs.



OK:

DTC B2795 is not output.




OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE KEY THAT CANNOT START ENGINE