Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2799 One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Wire harness or connector

·

Transponder key ECU

·

ECM


·

Start the engine and wait 10 seconds.*1

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2

*1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed.

*2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B365295E12
0.823,2.208 1.177,2.448 0.354,0.24 10 false ECM 5.542,1.99 5.844,2.208 0.302,0.219 10 false E96 5.51,2.146 6.979,2.5 1.469,0.354 10 false Transponder Key ECU Assembly 1.417,1.25 1.656,1.458 0.24,0.208 10 false IMI 1.76,1.188 2.021,1.385 0.26,0.198 10 false 40 1.75,0.427 2.042,0.625 0.292,0.198 10 false 29 0.813,2.021 2.615,2.302 1.802,0.281 10 false A38*1, A52*2 1.375,0.5 1.677,0.698 0.302,0.198 10 false IMO 5.865,0.51 6.188,0.708 0.323,0.198 10 false EFII 5.854,1.167 6.219,1.323 0.365,0.156 10 false EFIO 5.552,1.156 5.76,1.333 0.208,0.177 10 false 13 5.542,0.427 5.75,0.635 0.208,0.208 10 false 12 0.177,2.948 2.229,3.156 2.052,0.208 10 false *1: for LHD 0.177,3.219 2.156,3.521 1.979,0.302 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.


Result
Result Proceed to
OK A
NG (DTC B2799 is output) B
NG (Other DTCs are output) C



A

B

3.REGISTER ECU COMMUNICATION ID

C

3.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (ECU COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

5.REPLACE ECM
5.REPLACE ECM
a.

Temporarily replace the ECM with a new one or known good one.




NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (ECM WAS DEFECTIVE)

NG

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the E96 transponder key ECU assembly connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.


·

*1: for LHD

·

*2: for RHD


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E96-12 (EFII) - A38-29 (IMO) Always Below 1 Ω
E96-13 (EFIO) - A38-40 (IMI) Always Below 1 Ω
E96-12 (EFII) - Body ground Always 10 kΩ or higher
E96-13 (EFIO) - Body ground Always 10 kΩ or higher
A38-29 (IMO) - Body ground Always 10 kΩ or higher
A38-40 (IMI) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E96-12 (EFII) - A52-29 (IMO) Always Below 1 Ω
E96-13 (EFIO) - A52-40 (IMI) Always Below 1 Ω
E96-12 (EFII) - Body ground Always 10 kΩ or higher
E96-13 (EFIO) - Body ground Always 10 kΩ or higher
A52-29 (IMO) - Body ground Always 10 kΩ or higher
A52-40 (IMI) - Body ground Always 10 kΩ or higher




OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR