Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

The antenna coil receives key code signals from the transponder chip in the key grip. The antenna coil is built into the transponder key amplifier, which amplifies the key code signals and outputs the signals to the transponder key ECU assembly.

This DTC is stored when there is an open or short in the antenna coil.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2784 The antenna coil built into the transponder key amplifier is open or shorted (determined by communication with the transponder key ECU assembly) (1 trip detection logic*).
·

Terminal VC5, TXCT or CODE is open.

·

The antenna coil built into the transponder key amplifier is open.


·

Harness or connector

·

Transponder key amplifier

·

Transponder key ECU assembly


Insert the key into the ignition key cylinder.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2784 Antenna Coil Status

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

NG

3.CHECK TRANSPONDER KEY AMPLIFIER (OUTPUT)
3.CHECK TRANSPONDER KEY AMPLIFIER (OUTPUT)
a.
U164176E02
1.719,1.052 1.719,1.948 true 1.229,0.979 0.646,1.906 true 1.552,0.281 1.833,0.458 0.281,0.177 10 false E95 0.135,4.177 0.49,4.354 0.354,0.177 10 false GND 0.177,0.125 0.344,0.281 0.167,0.156 10 false *a 0.177,2.229 0.344,2.385 0.167,0.156 10 false *b 1.531,1.99 1.958,2.167 0.427,0.177 10 false CODE 0.406,1.958 0.833,2.135 0.427,0.177 10 false AGND

Using an oscilloscope, check the waveform.

Text in Illustration
*a Component with harness connected
(Transponder Key Amplifier)
*b Waveform

i.

Waveform (Reference)

Measurement Condition
Item Content
Tester Connection E95-4 (CODE) - E95-7 (AGND)
Tool Setting 1 V/DIV., 100 μs./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).





OK

4.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

4.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly (refer to the Service Bulletin).



NEXT

5.REGISTER KEY
5.REGISTER KEY
a.

Reregister the key (refer to the Service Bulletin).



NEXT

6.REGISTER ECU COMMUNICATION ID
6.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (refer to the Service Bulletin).



NEXT

7.CLEAR DTC
8.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG