Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2784 The antenna coil in the transponder key coil is open/shorted.
·

Harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


Insert the key into the ignition key cylinder.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2784 Antenna Coil Status

WIRING DIAGRAM

B329324E66
5.552,2.542 6.01,2.74 0.458,0.198 10 false E96 5.542,2.698 6.906,3.219 1.365,0.521 10 false Transponder Key ECU Assembly 1.292,3.042 1.75,3.24 0.458,0.198 10 false E176 1.281,3.188 2.75,3.49 1.469,0.302 10 false Transponder Key Coil 2.792,0.76 3.552,1.052 0.76,0.292 10 false ANT1 2.781,1.948 3.542,2.24 0.76,0.292 10 false ANT2 5.677,0.896 6.438,1.188 0.76,0.292 10 false ANT1 5.677,2.063 6.438,2.354 0.76,0.292 10 false ANT2 5.51,0.802 5.75,1.042 0.24,0.24 10 false 4 5.427,1.958 5.667,2.198 0.24,0.24 10 false 15 3.25,0.75 3.49,0.99 0.24,0.24 10 false 1 3.229,1.948 3.469,2.188 0.24,0.24 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

USE SIMULATION METHOD TO CHECK

NG

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the transponder key coil.



NEXT

4.CLEAR DTC
5.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

NG

6.CHECK TRANSPONDER KEY COIL (OUTPUT)
6.CHECK TRANSPONDER KEY COIL (OUTPUT)
a.

Using an oscilloscope, check the waveform.

U164297E02
3.333,0.802 3.229,1.083 true 3.823,0.781 3.927,1.063 true 3,1.104 3.417,1.292 0.417,0.188 10 false ANT2 3.833,1.115 4.25,1.302 0.417,0.188 10 false ANT1 3.385,0.094 3.781,0.25 0.396,0.156 10 false E176 6.563,4.563 6.979,4.75 0.417,0.188 10 false GND 6.563,2.49 6.979,2.677 0.417,0.188 10 false GND 0.104,0.063 0.333,0.26 0.229,0.198 10 false *a 0.979,3.563 1.208,3.76 0.229,0.198 10 false *c 0.979,1.469 1.208,1.667 0.229,0.198 10 false *b

Text in Illustration
*a Component with harness connected
(Transponder Key Coil)
*b Waveform 1
*c Waveform 2 - -

Waveform 1
Item Content
Tester Connection E176-1 (ANT1) - Body ground
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Within 3 seconds of inserting key into ignition key cylinder

Waveform 2
Item Content
Tester Connection E176-5 (ANT2) - Body ground
Tool Setting 2 V/DIV., 500 ms/DIV
Tool Setting Within 3 seconds of inserting key into ignition key cylinder

OK:

Waveform is similar to that shown in the illustration.




OK

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL)
7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.




NEXT

8.CLEAR DTC
9.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

10.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL)
a.

Disconnect the E96 transponder key ECU assembly connector.


b.

Disconnect the E176 transponder key coil connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E96-4 (ANT1) - E176-1 (ANT1) Always Below 1 Ω
E96-15 (ANT2) - E176-5 (ANT2) Always Below 1 Ω
E96-4 (ANT1) - Body ground Always 10 kΩ or higher
E176-1 (ANT1) - Body ground Always 10 kΩ or higher
E96-15 (ANT2) - Body ground Always 10 kΩ or higher
E176-5 (ANT2) - Body ground Always 10 kΩ or higher




OK

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.




NEXT

12.CLEAR DTC
13.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG