Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

When the engine immobiliser system is set, the security indicator light blinks continuously, but does not illuminate if the engine immobiliser system is not set.


WIRING DIAGRAM

B292706E04
1.802,0.51 2.615,0.667 0.813,0.156 10 false from Battery 5.635,1.031 5.823,1.188 0.188,0.156 10 false 2 5.875,1.135 6.354,1.292 0.479,0.156 10 false IG 5.625,1.76 5.813,1.917 0.188,0.156 10 false 8 5.625,2.375 5.813,2.531 0.188,0.156 10 false 5 5.51,2.906 5.865,3.063 0.354,0.156 10 false E96 5.844,2.438 6.323,2.594 0.479,0.156 10 false GND 5.865,0.531 6.344,0.688 0.479,0.156 10 false +B 5.635,0.427 5.75,0.583 0.115,0.156 10 false 1 4.083,1.302 4.865,1.458 0.781,0.156 10 false IG2 NO.1 1.24,1.146 2.646,1.302 1.406,0.156 10 false from IG2 MAIN Relay 1.292,1.75 1.396,1.906 0.104,0.156 10 false 8 2.688,1.74 2.927,1.896 0.24,0.156 10 false 3 1.49,1.885 1.719,2.042 0.229,0.156 10 false E 2.427,1.865 2.656,2.021 0.229,0.156 10 false LP 5.854,1.885 6.177,2.042 0.323,0.156 10 false IND 1.271,2.479 2.781,2.823 1.51,0.344 10 false Clock Assembly (Security Indicator Light) 1.292,2.26 1.865,2.5 0.573,0.24 10 false g2 4.094,0.688 4.896,0.844 0.802,0.156 10 false IMMOBI 5.51,3.073 6.927,3.49 1.417,0.417 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the transponder key ECU assembly, refer to Registration.



PROCEDURE

1.CHECK FOR DTC

OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Immobiliser
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -

OK:

Security indicator light can be turned on and off using the intelligent tester.




OK

3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - SECURITY INDICATOR LIGHT)
3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS)
a.

Turn the ignition switch off.

HINT:

When using the intelligent tester with the ignition switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds until communication between the intelligent tester and vehicle begins.



b.

Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DATA LIST / ACTIVE TEST).

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Immobiliser system status / Set or Unset Set: No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to ACC or off
Unset: Key in ignition key cylinder
-



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODYGROUND)
4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - SECURITY INDICATOR LIGHT)
a.

Disconnect the E96 transponder key ECU assembly connector.


b.

Disconnect the g2 clock assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E96-8 (IND) - g2-3 (LP) Always Below 1 Ω
g2-8 (E) - Body ground Always Below 1 Ω
g2-3 (LP) - Body ground Always 10 kΩ or higher




OK

5.REPLACE CLOCK ASSEMBLY (SECURITY INDICATOR LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE CLOCK ASSEMBLY (SECURITY INDICATOR LIGHT)
a.

Temporarily replace the clock assembly (security indicator light) with a new or normally functioning one (See page Vehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL).


b.

When the immobiliser is set or the theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.




OK

END (CLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODYGROUND)
a.

Disconnect the E96 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E96-5 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E96-1 (+B) - Body ground Always 11 to 14 V
E96-2 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR