Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B279A The communication line (IMI - EFIO) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*).
·

Harness or connector

·

Transponder key ECU assembly

·

ECM


Turn the ignition switch to ON and wait 6 seconds.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine start is prohibited

Related Data List and Active Test
DTC Code Data List and Active Test
B279A -

WIRING DIAGRAM

B288680E05
5.174,1.035 5.621,1.213 0.447,0.178 10 EFIO 1.826,1.035 2.083,1.213 0.257,0.178 10 IMI 1.275,1.863 2.177,2.009 0.902,0.146 10 A38*1, A52*2 0.358,2.298 1.260,2.444 0.902,0.146 10 *1: for LHD 0.358,2.515 1.260,2.661 0.902,0.146 10 *2: for RHD 4.942,1.863 5.209,2.009 0.267,0.146 10 E96 1.482,2.057 1.887,2.204 0.406,0.147 10 ECM 4.942,2.02 6.382,2.387 1.439,0.367 10 Transponder Key ECU Assembly 4.872,0.937 5.059,1.079 0.187,0.142 10 13 2.142,0.937 2.322,1.079 0.179,0.142 10 11

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

When replacing the ECM, refer to Initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.




OK

NG

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key amplifier assembly.

OK:

Connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the E96 transponder key ECU assembly connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E96-13 (EFIO) - A38-11 (IMI) Always Below 1 Ω
E96-13 (EFIO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E96-13 (EFIO) - A52-11 (IMI) Always Below 1 Ω
E96-13 (EFIO) - Body ground Always 10 kΩ or higher




OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly.



NEXT

6.REGISTER KEY
6.REGISTER KEY
a.

Register the key (refer to the Service Bulletin).



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (refer to the Service Bulletin).



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with the key.

OK:

Engine starts normally.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C



A

END (TRANSPONDER KEY ECU WAS DEFECTIVE)

B

C