Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B279A Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


Turn the ignition switch to ON and wait 6 seconds.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B365296E09
0.885,1.938 1.969,2.156 1.083,0.219 10 false A38*1, A52*2 1.115,2.125 1.51,2.344 0.396,0.219 10 false ECM 5.49,1.969 5.813,2.198 0.323,0.229 10 false E96 5.479,2.135 6.906,2.531 1.427,0.396 10 false Transponder Key ECU Assembly 1.469,1.125 1.698,1.333 0.229,0.208 10 false IMI 1.802,1 2.083,1.219 0.281,0.219 10 false 40 5.469,1.094 5.875,1.333 0.406,0.24 10 false EFIO 5.219,1.01 5.396,1.156 0.177,0.146 10 false 13 0.208,3.042 2.479,3.219 2.271,0.177 10 false *1: for LHD 0.208,3.333 2.188,3.635 1.979,0.302 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.




OK

NG

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the E96 transponder key ECU assembly connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

·

*1: for LHD

·

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E96-13 (EFIO) - A38-40 (IMI) Always Below 1 Ω
E96-13 (EFIO) - Body ground Always 10 kΩ or higher
A38-40 (IMI) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E96-13 (EFIO) - A52-40 (IMI) Always Below 1 Ω
E96-13 (EFIO) - Body ground Always 10 kΩ or higher
A52-40 (IMI) - Body ground Always 10 kΩ or higher




OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.



NEXT

6.CLEAR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C