Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

The key ID code of the transponder chip inside the IG key is compared against the key ID code registered in the transponder key ECU assembly. While checking the code, the transponder key ECU assembly supplies electrical power to the transponder chip in the key by means of the transponder key amplifier. If the codes match, the immobiliser is then UNSET (released), and after the engine start permission signal is sent to the ECM, if communication is functioning properly, engine start can be performed.

WIRING DIAGRAM

B255097E11
0.723,1.93 1.607,2.105 0.884,0.174 10 A38*1, A52*2 0.083,2.276 0.967,2.450 0.884,0.174 10 *1: for LHD 0.083,2.509 0.967,2.684 0.884,0.174 10 *2: for RHD 0.928,2.076 1.280,2.236 0.352,0.160 10 ECM 5.731,0.435 6.125,0.622 0.394,0.188 10 EFIO 5.731,1.198 6.125,1.386 0.394,0.188 10 EFII 1.286,0.435 1.520,0.622 0.234,0.188 10 IMI 1.237,1.198 1.520,1.386 0.283,0.188 10 IMO 5.442,0.336 5.666,0.546 0.224,0.210 10 13 5.442,1.082 5.666,1.292 0.224,0.210 10 12 5.533,1.93 5.944,2.117 0.410,0.186 10 E96 5.533,2.076 7.033,2.386 1.500,0.310 10 Transponder Key ECU Assembly 1.594,0.351 1.772,0.532 0.178,0.181 10 11 1.594,1.096 1.783,1.278 0.188,0.181 10 10

CAUTION / NOTICE / HINT

NOTICE:

When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


Result
Result Proceed to
No DTC output A
DTC output B



A

2.CONFIRM ENGINE MODEL

B

2.CONFIRM ENGINE MODEL
a.

Check the vehicle specifications.

Result
Result Proceed to
1GR-FE A
1VD-FTV B



A

3.READ VALUE USING INTELLIGENT TESTER

B

4.CHECK WHETHER ENGINE STARTS
3.READ VALUE USING INTELLIGENT TESTER
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Stored as Freeze Frame Data
Immobiliser Fuel Cut Status of immobiliser fuel cut/
ON or OFF
- Yes

OK:

The item in the Data List indicates "OFF".




OK

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Turn the ignition switch to ON, wait for 5 seconds, and then attempt to start the engine.

Result
Result Proceed to
Engine cannot be started A
Engine can be started B



A

5.CHECK ECM (TERMINAL IMI)

B

5.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U164183E02
3.51,2.948 3.188,3.26 true 4.979,0.708 5.542,2.167 true 2.115,2.708 2.448,2.885 0.333,0.177 10 false E96 5,0.115 5.26,0.292 0.26,0.177 10 false A38 5.427,0.115 5.688,0.292 0.26,0.177 10 false *A 6.385,0.115 6.646,0.292 0.26,0.177 10 false *B 6,0.115 6.26,0.292 0.26,0.177 10 false A52 5.448,2.198 5.802,2.375 0.354,0.177 10 false IMI 0.198,0.125 0.365,0.281 0.167,0.156 10 false *a 0.646,3.344 0.813,3.5 0.167,0.156 10 false *c 0.646,5.229 0.813,5.385 0.167,0.156 10 false *d 2.958,3.302 3.313,3.479 0.354,0.177 10 false EFIO 0.563,4.573 0.927,4.75 0.365,0.177 10 false GND 0.563,6.365 0.927,6.542 0.365,0.177 10 false GND 1.625,4.677 1.792,4.833 0.167,0.156 10 false *e 1.427,6.469 1.594,6.625 0.167,0.156 10 false *e 2.208,2.219 2.375,2.375 0.167,0.156 10 false *b

Text in Illustration
*A for LHD *B for RHD
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform A - -

Measurement Condition
Item Content
Tester Connection A38-11 (IMI) - E96-13 (EFIO)*1
A52-11 (IMI) - E96-13 (EFIO)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected

*1: for LHD

*2: for RHD


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform A) not output, or has abnormal wavelength or shape B



A

6.CHECK ECM (TERMINAL IMO)

B

10.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY)
6.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

U164184E02
3.573,2.958 3.323,3.271 true 5.094,0.719 5.667,2.177 true 2.104,2.708 2.406,2.885 0.302,0.177 10 false E96 5.083,0.135 5.344,0.313 0.26,0.177 10 false A38 5.448,0.135 5.708,0.313 0.26,0.177 10 false *A 6.354,0.135 6.615,0.313 0.26,0.177 10 false *B 6,0.135 6.26,0.313 0.26,0.177 10 false A52 5.573,2.208 5.927,2.385 0.354,0.177 10 false IMO 0.177,0.135 0.344,0.292 0.167,0.156 10 false *a 0.625,3.354 0.792,3.51 0.167,0.156 10 false *c 0.625,5.24 0.792,5.396 0.167,0.156 10 false *d 3.167,3.292 3.521,3.469 0.354,0.177 10 false EFII 0.552,4.583 0.917,4.76 0.365,0.177 10 false GND 0.552,6.375 0.917,6.552 0.365,0.177 10 false GND 1.604,3.75 1.771,3.906 0.167,0.156 10 false *e 1.385,5.552 1.552,5.708 0.167,0.156 10 false *e 2.198,2.219 2.365,2.375 0.167,0.156 10 false *b 1.75,4.698 1.917,4.854 0.167,0.156 10 false *g 1.552,6.51 1.719,6.667 0.167,0.156 10 false *h 1.177,6.51 1.344,6.667 0.167,0.156 10 false *f 1.156,4.719 1.323,4.875 0.167,0.156 10 false *f

Text in Illustration
*A for LHD *B for RHD
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform B *f 160 ms
*g 510 ms *h 270 ms

Measurement Condition
Item Content
Tester Connection A38-10 (IMO) - E96-12 (EFII)*1
A52-10 (IMO) - E96-12 (EFII)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected

*1: for LHD

*2: for RHD


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform B) not output, or has abnormal wavelength or shape (for 1GR-FE) B
Waveform 1 or 2 (Waveform B) not output, or has abnormal wavelength or shape (for 1VD-FTV) C



A

7.CHECK ECM (TERMINAL IMI)

B

C

7.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U164185E02
3.531,2.927 3.208,3.25 true 4.938,0.719 5.5,2.177 true 2.104,2.688 2.396,2.865 0.292,0.177 10 false E96 5.135,0.115 5.396,0.292 0.26,0.177 10 false A38 5.552,0.115 5.813,0.292 0.26,0.177 10 false *A 6.333,0.115 6.594,0.292 0.26,0.177 10 false *B 5.969,0.115 6.229,0.292 0.26,0.177 10 false A52 5.406,2.198 5.76,2.375 0.354,0.177 10 false IMI 0.167,0.115 0.333,0.271 0.167,0.156 10 false *a 0.615,3.333 0.781,3.49 0.167,0.156 10 false *c 0.615,5.219 0.781,5.375 0.167,0.156 10 false *d 3.063,3.271 3.417,3.448 0.354,0.177 10 false EFIO 0.552,4.563 0.917,4.74 0.365,0.177 10 false GND 0.552,6.365 0.917,6.542 0.365,0.177 10 false GND 2.844,3.677 3.01,3.833 0.167,0.156 10 false *e 2.979,4.688 3.146,4.844 0.167,0.156 10 false *g 2.375,4.688 2.542,4.844 0.167,0.156 10 false *f 2.375,6.479 2.542,6.635 0.167,0.156 10 false *h 2,6.479 2.167,6.635 0.167,0.156 10 false *f 2.24,5.49 2.406,5.646 0.167,0.156 10 false *e 2.188,2.198 2.354,2.354 0.167,0.156 10 false *b

Text in Illustration
*A for LHD *B for RHD
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform C *f 160 ms
*g 510 ms *h 270 ms

Measurement Condition
Item Content
Tester Connection A38-11 (IMI) - E96-13 (EFIO)*1
A52-11 (IMI) - E96-13 (EFIO)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected

*1: for LHD

*2: for RHD


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform C) not output, or has abnormal wavelength or shape B



A

8.REGISTER ECU COMMUNICATION ID

B

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
8.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (refer to the Service Bulletin).



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with the key.

OK:

Engine starts normally.




OK

END

NG

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
10.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY)
a.

for LHD:

i.

Disconnect the A38 ECM connector.


ii.

Disconnect the E96 transponder key ECU assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-11 (IMI) - E96-13 (EFIO) Always Below 1 Ω
E96-13 (EFIO) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the A52 ECM connector.


ii.

Disconnect the E96 transponder key ECU assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-11 (IMI) - E96-13 (EFIO) Always Below 1 Ω
E96-13 (EFIO) - Body ground Always 10 kΩ or higher





OK

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly.


b.

Check that the engine starts with the key.

OK:

Engine starts normally.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C



A

END

B

C