Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B365295E13
0.813,2.208 1.25,2.458 0.438,0.25 10 false ECM 5.51,1.958 5.823,2.156 0.313,0.198 10 false E96 5.51,2.135 6.938,2.51 1.427,0.375 10 false Transponder Key ECU Assembly 1.417,1.302 1.719,1.521 0.302,0.219 10 false IMI 1.719,1.115 1.979,1.323 0.26,0.208 10 false 40 1.719,0.396 2.01,0.594 0.292,0.198 10 false 29 0.813,2.021 2.625,2.271 1.813,0.25 10 false A38*1, A52*2 1.375,0.49 1.708,0.688 0.333,0.198 10 false IMO 5.865,0.5 6.156,0.656 0.292,0.156 10 false EFII 5.854,1.229 6.219,1.385 0.365,0.156 10 false EFIO 5.563,1.146 5.74,1.292 0.177,0.146 10 false 13 5.604,0.427 5.781,0.583 0.177,0.156 10 false 12 0.177,2.948 2.229,3.156 2.052,0.208 10 false *1: for LHD 0.177,3.219 2.156,3.521 1.979,0.302 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

OK:

DTC is not output.


Result
Result Proceed to
OK (1GR-FE) A
OK (1VD-FTV) B
NG C



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK WHETHER ENGINE STARTS

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Engine and ECT
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut / OFF/ON ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off
-

OK:

The item in the Data List indicates "OFF".




OK

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

B

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to Service Bulletin.




NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

7.REPLACE ECM
7.REPLACE ECM
a.

Temporarily replace the ECM with a new or known good one.




NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (ECM WAS DEFECTIVE)

NG

9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the E96 transponder key ECU assembly connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

·

*1: for LHD

·

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E96-12 (EFII) - A38-29 (IMO) Always Below 1 Ω
E96-13 (EFIO) - A38-40 (IMI) Always Below 1 Ω
E96-12 (EFII) - Body ground Always 10 kΩ or higher
E96-13 (EFIO) - Body ground Always 10 kΩ or higher
A38-29 (IMO) - Body ground Always 10 kΩ or higher
A38-40 (IMI) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E96-12 (EFII) - A52-29 (IMO) Always Below 1 Ω
E96-13 (EFIO) - A52-40 (IMI) Always Below 1 Ω
E96-12 (EFII) - Body ground Always 10 kΩ or higher
E96-13 (EFIO) - Body ground Always 10 kΩ or higher
A52-29 (IMO) - Body ground Always 10 kΩ or higher
A52-40 (IMI) - Body ground Always 10 kΩ or higher




OK

10.CHECK TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly. Refer to Service Bulletin.



b.

Using a registered key, turn the ignition switch to ON.


c.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C