Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM(w/o Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255575 THEFT DETERRENT SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/o Entry and Start System)  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is built into the hood lock. This switch turns on when the engine hood is opened and turns off when the engine hood is closed.


WIRING DIAGRAM

B294199E01
4.742,1.713 6.616,2.059 1.875,0.346 10 Main Body ECU (Cowl Side Junction Block Assembly LH) 4.742,1.527 5.064,1.683 0.323,0.156 10 E1 1.943,1.501 3.835,1.897 1.892,0.395 10 Hood Lock Assembly (Engine Hood Courtesy Switch) 1.943,1.357 2.181,1.512 0.238,0.156 10 A8 4.752,1.023 5.241,1.178 0.489,0.156 10 HCTY 4.42,0.906 4.623,1.062 0.202,0.156 10 16 2.907,0.915 3.023,1.071 0.116,0.156 10 2 2.111,0.918 2.243,1.074 0.132,0.156 10 1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE HOOD COURTESY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Hood Courtesy Switch Engine hood courtesy switch /
ON or OFF
ON: Engine hood open
OFF: Engine hood closed
-

OK:

ON (engine hood is open) appears on screen.




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK ASSEMBLY LH)

NG

2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
a.

for LHD:

B219990E03
1.008,2.132 1.275,2.304 0.267,0.172 10 *a 3.633,2.132 3.900,2.304 0.267,0.172 10 *b

Text in Illustration
*a Unlock Position *b Lock Position


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Unlock position 10 kΩ or higher
1 - 2 Lock position Below 1 Ω




b.

for RHD:

B219989E03
1.416,2.205 2.186,2.355 0.770,0.149 10 *a 3.927,2.205 4.789,2.355 0.862,0.149 10 *b

Text in Illustration
*a Unlock Position *b Lock Position


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Unlock position 10 kΩ or higher
1 - 2 Lock position Below 1 Ω





OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HOOD LOCK AND BODY GROUND)

NG

REPLACE HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HOOD LOCK AND BODY GROUND)
a.

Disconnect the E30 main body ECU connector.


b.

Disconnect the E1 hood courtesy switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-16 (HCTY) - A8-2 Always Below 1 Ω
A8-1 - Body ground Always Below 1 Ω
E1-16 (HCTY) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR