Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM(w/o Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255575 THEFT DETERRENT SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/o Entry and Start System)  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (cowl side junction block assembly LH) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B184350E09
0.297,0.633 0.813,1.018 0.516,0.385 10 from Battery 1.333,0.855 2.115,1.044 0.783,0.189 10 SECURITY 2.37,1.417 3.597,1.606 1.227,0.189 10 SECURITY HORN 5.542,0.706 5.873,0.877 0.332,0.171 10 SH 5.32,0.592 5.536,0.780 0.216,0.188 10 6 5.472,1.555 5.750,1.715 0.278,0.159 10 E4 5.472,1.696 6.800,2.224 1.328,0.527 10 Main Body ECU (Cowl Side Junction Block Assembly LH) 3.856,1.916 4.244,2.127 0.387,0.211 10 A19 3.856,2.067 4.762,2.418 0.906,0.350 10 Security Horn Assembly 3.546,1.823 3.769,2.018 0.223,0.195 10 1 3.28,0.583 3.502,0.778 0.223,0.195 10 1 2.537,0.583 2.711,0.778 0.174,0.195 10 2 2.523,1.157 2.649,1.352 0.126,0.195 10 5 3.28,1.157 3.502,1.352 0.223,0.195 10 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Horn Security horn ON / OFF -


OK:

The security horn assembly sounds and stops correctly when operated through the intelligent tester.



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK ASSEMBLY LH)

NG

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY
a.
E140469E01
2.273,1.236 2.196,0.643 2.196,0.643 2.007,0.643 false 1.869,0.565 1.970,0.721 0.100,0.156 10 1

Remove the security horn assembly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY HORN ASSEMBLY>REMOVAL).


b.

Check the operation of the security horn assembly.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 Horn sounds
Battery negative (-) → Horn body




OK

3.INSPECT SECURITY HORN RELAY

NG

3.INSPECT SECURITY HORN RELAY
a.
E145692E26
2.667,0.708 3.052,0.708 false 1.615,0.719 1.99,0.719 false 2.542,1.125 3.052,1.125 false 2.542,1.646 3.052,1.646 false 0.208,1.313 0.365,1.49 0.156,0.177 10 false 1 1.208,1.302 1.365,1.479 0.156,0.177 10 false 2 0.198,0.771 0.354,0.948 0.156,0.177 10 false 3 1.188,0.75 1.344,0.927 0.156,0.177 10 false 5 0.073,0.021 0.323,0.198 0.25,0.177 10 false *a 1.5,0.615 1.656,0.792 0.156,0.177 10 false 1 3.094,0.615 3.25,0.792 0.156,0.177 10 false 2 3.083,1.583 3.24,1.76 0.156,0.177 10 false 3 3.104,1.042 3.26,1.219 0.156,0.177 10 false 5

Remove the SECURITY HORN relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
(when battery voltage is not applied between terminals 1 and 2)
3 - 5 Below 1 Ω
(when battery voltage is applied between terminals 1 and 2)


Text in Illustration
*a SECURITY HORN Relay



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - SECURITY HORN RELAY)

NG

REPLACE SECURITY HORN RELAY

4.CHECK HARNESS AND CONNECTOR (BATTERY - SECURITY HORN RELAY)
a.
B292777E01
0.181,0.154 0.332,0.292 0.151,0.139 10 *a 2.123,1.211 2.274,1.349 0.151,0.139 10 *b

Remove the SECURITY HORN relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly SECURITY HORN relay terminal 2- Body ground Always 11 to 14 V
Engine room relay block and junction block assembly SECURITY HORN relay terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*a Engine Room Relay Block
*b SECURITY HORN Relay



OK

5.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - SECURITY HORN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - SECURITY HORN ASSEMBLY)
a.

Remove the SECURITY HORN relay from the engine room relay block.


b.

Disconnect the A19 security horn assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly SECURITY HORN relay terminal 3 - A19-1 Always Below 1 Ω
Engine room relay block and junction block assembly SECURITY HORN relay terminal 3 - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - MAIN BODY ECU)
a.

Remove the SECURITY HORN relay from the engine room relay block.


b.

Disconnect the E4 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly SECURITY HORN relay terminal 2 - E4-6 (SH) Always Below 1 Ω
Engine room relay block and junction block assembly SECURITY HORN relay terminal 2 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR