Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255575 THEFT DETERRENT SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/o Entry and Start System)  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator will flash continuously if the immobiliser system is set, or not illuminate if the immobiliser system is not set.

When the theft deterrent system is in the armed state, the immobiliser system is automatically set and the security indicator will flash continuously.

When the theft deterrent system is in the arming preparation state or alarm sounding state, the main body ECU (cowl side junction block assembly LH) causes the security indicator to be illuminated.


WIRING DIAGRAM

B184353E19
0.932,1.83 1.240,2.031 0.309,0.201 10 g1 0.932,1.992 2.505,2.362 1.574,0.370 10 Clock Assembly (Security Indicator Light) 1.867,1.401 2.099,1.587 0.232,0.186 10 1 4.728,0.845 4.840,1.031 0.111,0.186 10 4 1.867,0.845 2.099,1.031 0.232,0.186 10 9 1.646,1.398 1.773,1.538 0.126,0.140 10 E 1.607,0.862 1.810,1.002 0.203,0.140 10 LP 4.95,0.968 5.274,1.154 0.324,0.186 10 IND 4.764,2.05 5.069,2.202 0.305,0.151 10 E4 4.764,2.21 6.904,2.572 2.140,0.363 10 Main Body ECU (Cowl Side Junction Block Assembly LH)

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator ON / OFF -

OK:

Security indicator illuminates.




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK ASSEMBLY LH)

NG

2.CHECK HARNESS AND CONNECTOR (CLOCK - MAIN BODY ECU AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (CLOCK - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the g1 clock assembly connector.


b.

Disconnect the E4 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g1-9 (LP) - E4-4 (IND) Always Below 1 Ω
g1-1 (E) - Body ground Always Below 1 Ω
g1-9 (LP) - Body ground Always 10 kΩ or higher




OK

3.REPLACE CLOCK ASSEMBLY (SECURITY INDICATOR LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE CLOCK ASSEMBLY (SECURITY INDICATOR LIGHT)
a.

Temporarily replace the clock assembly (security indicator light) with a new or normally functioning one (See page Vehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL).


b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light is illuminated.

OK:

Security indicator light is illuminated.




OK

END (CLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK ASSEMBLY LH)