Home › Vehicle Interior › MIRROR (INT) › INNER REAR VIEW MIRROR › from 2015.08
RM2660E _58 Vehicle Interior _052842 MIRROR (INT) _0255600 INNER REAR VIEW MIRROR G

MIRROR (INT)  INNER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87810 1.INSPECT INNER REAR VIEW MIRROR ASSEMBLY (for Standard)

a.

Check operation of the electrochromic inner mirror.

B428635E03
0.781,1.771 0.781,2.313 true 1.469,2.052 1.823,2.052 false 3.417,0.875 3.552,1.354 true 3.542,0.99 3.813,0.99 true 3.542,0.844 3.802,0.656 true 2.844,0.646 3.083,0.813 true 2.906,1.24 3.177,0.885 true 1.875,1.99 2.198,2.271 0.323,0.281 10 false *1 0.698,2.375 1.021,2.656 0.323,0.281 10 false *2 2.177,1.24 2.5,1.521 0.323,0.281 10 false *3 3.792,0.292 4.115,0.573 0.323,0.281 10 false *a 5.115,1.156 5.438,1.438 0.323,0.281 10 false *b 5.146,2.156 5.469,2.438 0.323,0.281 10 false *c 3.573,1.323 3.896,1.604 0.323,0.281 10 false E 3.833,0.521 4.156,0.802 0.323,0.281 10 false IG 3.854,0.917 4.177,1.198 0.323,0.281 10 false B 2.646,0.5 2.99,0.698 0.344,0.198 10 false EC- 2.719,1.26 3.063,1.458 0.344,0.198 10 false EC+

Text in Illustration
*1 Black Colored Tape *2 Forward Sensor
*3 Battery - -
*a Component without harness connected (Inner Rear View Mirror Assembly) *b Bright
*c Dark - -

i.

Connect the battery positive (+) lead to terminal 1 (IG) and the negative (-) lead to terminal 2 (E).


ii.

Press the AUTO switch.


iii.

Attach black colored tape to the forward sensor to prevent it from sensing light.


iv.

Shine an electric light on the mirror. Check that the mirror surface changes from bright to dark.

HINT:

When the environment is very bright, the antiglare operation may occur immediately after the tape is applied.



v.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 - 5 Inner rear view mirror surface
Bright → Dark
Below 1 V → 1.25 V


If the result is not as specified, replace the inner rear view mirror assembly.



Hide 87810 2.INSPECT INNER REAR VIEW MIRROR ASSEMBLY (w/ Adaptive High Beam System)

a.

Check operation of the electrochromic inner mirror.

B428636E05
0.813,1.75 0.813,2.292 true 1.406,2.135 1.76,2.135 false 3.406,0.917 3.531,1.365 true 3.531,1.021 3.854,1.021 true 3.531,0.865 3.792,0.677 true 2.813,0.677 3.073,0.854 true 2.906,1.271 3.177,0.917 true 1.813,2.063 2.135,2.344 0.323,0.281 10 false *1 0.74,2.365 1.063,2.646 0.323,0.281 10 false *2 2.177,1.25 2.5,1.531 0.323,0.281 10 false *3 3.76,0.365 4.083,0.646 0.323,0.281 10 false *a 5.135,1.188 5.458,1.469 0.323,0.281 10 false *b 5.167,2.167 5.49,2.448 0.323,0.281 10 false *c 3.542,1.354 3.865,1.635 0.323,0.281 10 false E 3.833,0.594 4.156,0.875 0.323,0.281 10 false IG 3.885,0.948 4.208,1.229 0.323,0.281 10 false B 2.646,0.521 2.99,0.719 0.344,0.198 10 false EC- 2.708,1.292 3.052,1.49 0.344,0.198 10 false EC+

Text in Illustration
*1 Black Colored Tape *2 Forward Sensor
*3 Battery - -
*a Component without harness connected (Inner Rear View Mirror Assembly) *b Bright
*c Dark - -

i.

Connect the battery positive (+) lead to terminal 1 (IG) and the negative (-) lead to terminal 2 (E).


ii.

Press the AUTO switch.


iii.

Attach black colored tape to the forward sensor to prevent it from sensing light.


iv.

Shine an electric light on the mirror. Check that the mirror surface changes from bright to dark.

HINT:

When the environment is very bright, the antiglare operation may occur immediately after the tape is applied.



v.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 - 5 Inner rear view mirror surface
Bright → Dark
Below 1 V → 1.25 V


If the result is not as specified, replace the inner rear view mirror assembly.



Hide 87810 3.INSPECT INNER REAR VIEW MIRROR ASSEMBLY (w/ Pre-collision System)

a.

Check operation of the electrochromic inner mirror.

E332941E04
0.781,1.917 0.781,2.469 true 1.469,2.167 1.823,2.167 false 3.677,1.094 4,1.094 true 3.688,0.948 3.948,0.76 true 2.979,0.729 3.24,0.917 true 2.979,1.281 3.333,1 true 3.552,0.99 3.552,1.333 3.552,1.333 3.969,1.333 true 1.865,2.073 2.188,2.354 0.323,0.281 10 false *1 0.719,2.51 1.042,2.792 0.323,0.281 10 false *2 2.25,1.333 2.573,1.615 0.323,0.281 10 false *3 3.958,0.438 4.281,0.719 0.323,0.281 10 false *a 5.104,1.125 5.427,1.406 0.323,0.281 10 false *b 5.167,2.177 5.49,2.458 0.323,0.281 10 false *c 4.021,1.25 4.344,1.531 0.323,0.281 10 false E 4.01,0.677 4.333,0.958 0.323,0.281 10 false IG 4.063,1.021 4.385,1.302 0.323,0.281 10 false B 2.708,0.646 3.052,0.844 0.344,0.198 10 false EC- 2.708,1.26 3.052,1.458 0.344,0.198 10 false EC+

Text in Illustration
*1 Black Colored Tape *2 Forward Sensor
*3 Battery - -
*a Component without harness connected (Inner Rear View Mirror Assembly) *b Bright
*c Dark - -

i.

Connect the battery positive (+) lead to terminal 1 (IG) and the negative (-) lead to terminal 2 (E).


ii.

Press the AUTO switch.


iii.

Attach black colored tape to the forward sensor to prevent it from sensing light.


iv.

Shine an electric light on the mirror. Check that the mirror surface changes from bright to dark.

HINT:

When the environment is very bright, the antiglare operation may occur immediately after the tape is applied.



v.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (EC+) - 5 (EC-) Inner rear view mirror surface
Bright → Dark
Below 1 V → 1.25 V


If the result is not as specified, replace the inner rear view mirror assembly.