Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the center airbag sensor. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C178005E05
1.458,2.525 2.724,2.681 1.266,0.156 10 A38*1, A52*2 1.555,5.01 2.821,5.166 1.266,0.156 10 *1: for LHD 1.555,5.311 2.821,5.467 1.266,0.156 10 *2: for RHD 1.458,2.707 1.787,2.863 0.330,0.156 10 ECM 1.458,4.199 1.760,4.404 0.302,0.205 10 E22 1.458,4.382 1.885,4.544 0.427,0.163 10 DLC3 5.794,4.697 6.124,4.860 0.330,0.163 10 E47 5.794,4.872 7.159,5.049 1.364,0.177 10 Center Airbag Sensor 0.56,5.314 1.494,5.484 0.934,0.170 10 : CAN Line 1.139,3.53 1.302,3.707 0.163,0.177 10 4 2.088,3.555 2.293,3.732 0.205,0.177 10 13 1.325,3.653 1.585,3.927 0.260,0.274 10 CG 1.797,3.653 2.169,3.878 0.371,0.225 10 TC 1.598,0.648 1.990,0.831 0.392,0.184 10 CANL 0.076,0.006 2.907,0.220 2.831,0.214 12 for 1GR-FE, 1UR-FE, 3UR-FE: 1.584,1.199 1.997,1.348 0.413,0.149 10 CANH 6.068,0.648 6.460,0.831 0.392,0.184 10 CANL 6.068,1.199 6.480,1.348 0.413,0.149 10 CANH 1.794,1.762 2.047,1.924 0.253,0.163 10 TC 2.088,0.522 2.272,0.698 0.184,0.177 10 11 2.081,1.089 2.286,1.266 0.205,0.177 10 10 2.106,1.664 2.318,1.847 0.211,0.184 10 16 5.799,0.505 6.048,0.680 0.248,0.174 10 22 5.78,1.066 6.057,1.305 0.276,0.239 10 13

C178005E06
1.46,2.525 2.824,2.680 1.364,0.156 10 A38*1, A52*2 1.544,5.046 2.908,5.202 1.364,0.156 10 *1: for LHD 1.544,5.327 2.908,5.482 1.364,0.156 10 *2: for RHD 1.46,2.707 1.789,2.863 0.330,0.156 10 ECM 1.46,4.199 1.761,4.403 0.302,0.205 10 E22 1.46,4.381 1.886,4.544 0.427,0.163 10 DLC3 5.796,4.696 6.125,4.859 0.330,0.163 10 E47 5.796,4.871 7.160,5.048 1.364,0.177 10 Center Airbag Sensor 0.562,5.314 1.495,5.484 0.934,0.170 10 : CAN Line 1.141,3.53 1.304,3.706 0.163,0.177 10 4 2.09,3.554 2.295,3.731 0.205,0.177 10 13 1.326,3.652 1.587,3.926 0.260,0.274 10 CG 1.799,3.652 2.170,3.878 0.371,0.225 10 TC 1.6,0.647 1.992,0.831 0.392,0.184 10 CANL 0.078,0.005 1.830,0.189 1.752,0.184 12 for 1VD-FTV: 1.586,1.198 1.998,1.347 0.413,0.149 10 CANH 6.069,0.647 6.461,0.831 0.392,0.184 10 CANL 6.069,1.198 6.482,1.347 0.413,0.149 10 CANH 1.796,1.761 2.049,1.924 0.253,0.163 10 TC 2.09,0.521 2.274,0.698 0.184,0.177 10 49 2.083,1.088 2.288,1.265 0.205,0.177 10 41 2.108,1.663 2.319,1.847 0.211,0.184 10 27 5.8,0.505 6.049,0.679 0.248,0.174 10 22 5.782,1.065 6.058,1.304 0.276,0.239 10 13

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

B

C

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.
U164733E01
0.066,0.049 1.342,0.248 1.275,0.199 10 Front view of DLC3: 0.254,1.44 0.574,1.594 0.320,0.153 10 E22 1.92,2.143 2.194,2.327 0.275,0.184 10 TC 0.066,2.37 2.408,2.746 2.342,0.376 10 Front view of wire harness connector: (to ECM) 2.776,3.189 3.120,3.375 0.344,0.186 10 TC*1 2.532,3.453 2.876,3.639 0.344,0.186 10 TC*2 0.027,4.044 2.182,4.194 2.155,0.151 10 *1: for 1GR-FE, 1UR-FE, 3UR-FE 1.474,4.359 2.254,4.509 0.780,0.151 10 *3: for LHD 0.027,4.355 1.070,4.505 1.043,0.151 10 *2: for 1VD-FTV 2.505,4.36 3.264,4.511 0.759,0.151 10 *4: for RHD 0.219,3.147 0.559,3.320 0.340,0.174 10 A38 0.631,3.147 0.972,3.320 0.340,0.174 10 *3 0.631,3.559 0.972,3.733 0.340,0.174 10 *4 1.828,1.866 1.998,2.124 false 0.201,3.559 0.542,3.733 0.340,0.174 10 A52 1.991,3.482 2.507,3.53 false 1.97,3.409 2.74,3.272 false

Turn the ignition switch off.


b.

Disconnect the A38 connector from the ECM.


c.

for LHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1UR-FE, 3UR-FE:
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-16 (TC) Always Below 1 Ω


for 1VD-FTV:
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-27 (TC) Always Below 1 Ω




d.

for RHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1UR-FE, 3UR-FE:
Tester Connection Condition Specified Condition
E22-13 (TC) - A52-16 (TC) Always Below 1 Ω


for 1VD-FTV:
Tester Connection Condition Specified Condition
E22-13 (TC) - A52-27 (TC) Always Below 1 Ω





OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
U156867E01
0.056,0.045 1.330,0.221 1.274,0.177 10 Front view of DLC3: 0.156,1.185 0.486,1.340 0.330,0.156 10 E22 1.832,1.806 2.162,1.962 0.330,0.156 10 CG 1.606,1.033 1.965,1.761 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-4 (CG) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (TC OF ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC OF ECM - BODY GROUND)
U164735E01
0.124,0.088 2.513,0.427 2.389,0.339 10 Front view of wire harness connector: (to ECM) 0.21,1.602 0.512,1.786 0.302,0.184 10 A38 0.68,1.602 0.981,1.786 0.302,0.184 10 *3 0.68,1.997 0.981,2.181 0.302,0.184 10 *4 2.769,1.666 3.142,1.834 0.373,0.167 10 TC*1 2.47,1.965 2.843,2.132 0.373,0.167 10 TC*2 0.067,2.61 2.491,2.777 2.424,0.167 10 *1: for 1GR-FE, 1UR-FE, 3UR-FE 1.445,2.977 2.214,3.144 0.769,0.167 10 *3: for LHD 2.485,2.977 3.240,3.144 0.755,0.167 10 *4: for RHD 0.067,2.977 1.104,3.144 1.037,0.167 10 *2: for 1VD-FTV 0.21,2.014 0.512,2.198 0.302,0.184 10 A52 1.978,1.881 2.724,1.762 false 1.988,1.95 2.414,2.042 false

a.

for LHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1UR-FE, 3UR-FE:
Tester Connection Condition Specified Condition
A38-16 (TC) - Body ground Always 1 MΩ or higher


for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-27 (TC) - Body ground Always 1 MΩ or higher




b.

for RHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2UZ-FE, 3UR-FE:
Tester Connection Condition Specified Condition
A52-16 (TC) - Body ground Always 1 MΩ or higher


for 1GR-FE, 1VD-FTV:
Tester Connection Condition Specified Condition
A52-27 (TC) - Body ground Always 1 MΩ or higher





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU