Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the center airbag sensor. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C178005E09
1.333,2.479 2.49,2.677 1.156,0.198 10 false A38*1, A52*2 1.552,4.938 2.625,5.167 1.073,0.229 10 false *1: for LHD 1.552,5.24 2.573,5.479 1.021,0.24 10 false *2: for RHD 1.333,2.688 1.667,2.844 0.333,0.156 10 false ECM 1.5,4.146 1.802,4.354 0.302,0.208 10 false E22 1.5,4.344 1.927,4.51 0.427,0.167 10 false DLC3 5.792,4.698 6.125,4.865 0.333,0.167 10 false E47 5.792,4.885 7.156,5.063 1.365,0.177 10 false Center Airbag Sensor 0.563,5.302 1.5,5.469 0.938,0.167 10 false : CAN Line 1.135,3.521 1.302,3.698 0.167,0.177 10 false 4 2.104,3.531 2.313,3.708 0.208,0.177 10 false 13 1.344,3.625 1.604,3.896 0.26,0.271 10 false CG 1.844,3.635 2.219,3.865 0.375,0.229 10 false TC 1.635,0.635 2.031,0.823 0.396,0.188 10 false CANL 0.073,0.052 1.792,0.344 1.719,0.292 12 false for 1GR-FE, 1UR-FE: 1.604,1.198 2.021,1.344 0.417,0.146 10 false CANH 6.083,0.635 6.479,0.823 0.396,0.188 10 false CANL 6.083,1.167 6.5,1.313 0.417,0.146 10 false CANH 1.823,1.771 2.073,1.938 0.25,0.167 10 false TC 2.125,0.479 2.313,0.656 0.188,0.177 10 false 11 2.125,1.042 2.333,1.219 0.208,0.177 10 false 10 2.135,1.625 2.344,1.813 0.208,0.188 10 false 16 5.802,0.479 6.052,0.656 0.25,0.177 10 false 22 5.781,1.052 6.052,1.292 0.271,0.24 10 false 13

C178005E08
1.556,2.497 1.982,2.699 0.426,0.202 10 A38 1.556,2.651 1.886,2.807 0.330,0.156 10 ECM 1.528,4.157 1.830,4.362 0.302,0.205 10 E22 1.528,4.311 1.955,4.474 0.427,0.163 10 DLC3 5.794,4.697 6.124,4.860 0.330,0.163 10 E47 5.794,4.872 7.159,5.049 1.364,0.177 10 Center Airbag Sensor 0.56,5.314 1.494,5.484 0.934,0.170 10 : CAN Line 1.167,3.516 1.330,3.693 0.163,0.177 10 4 2.116,3.541 2.321,3.718 0.205,0.177 10 13 1.353,3.639 1.613,3.913 0.260,0.274 10 CG 1.825,3.639 2.197,3.864 0.371,0.225 10 TC 1.64,0.634 2.032,0.817 0.392,0.184 10 CANL 0.076,0.006 1.212,0.220 1.136,0.214 12 for 3UR-FE: 1.626,1.185 2.039,1.334 0.413,0.149 10 CANH 6.068,0.648 6.460,0.831 0.392,0.184 10 CANL 6.068,1.199 6.480,1.348 0.413,0.149 10 CANH 1.836,1.748 2.089,1.910 0.253,0.163 10 TC 2.137,0.494 2.321,0.670 0.184,0.177 10 19 2.137,1.061 2.342,1.238 0.205,0.177 10 11 2.137,1.636 2.349,1.819 0.211,0.184 10 43 5.799,0.505 6.048,0.680 0.248,0.174 10 22 5.78,1.066 6.057,1.305 0.276,0.239 10 13

C178005E06
1.46,2.525 2.824,2.680 1.364,0.156 10 A38*1, A52*2 1.544,5.046 2.908,5.202 1.364,0.156 10 *1: for LHD 1.544,5.327 2.908,5.482 1.364,0.156 10 *2: for RHD 1.46,2.707 1.789,2.863 0.330,0.156 10 ECM 1.46,4.199 1.761,4.403 0.302,0.205 10 E22 1.46,4.381 1.886,4.544 0.427,0.163 10 DLC3 5.796,4.696 6.125,4.859 0.330,0.163 10 E47 5.796,4.871 7.160,5.048 1.364,0.177 10 Center Airbag Sensor 0.562,5.314 1.495,5.484 0.934,0.170 10 : CAN Line 1.141,3.53 1.304,3.706 0.163,0.177 10 4 2.09,3.554 2.295,3.731 0.205,0.177 10 13 1.326,3.652 1.587,3.926 0.260,0.274 10 CG 1.799,3.652 2.170,3.878 0.371,0.225 10 TC 1.6,0.647 1.992,0.831 0.392,0.184 10 CANL 0.078,0.005 1.830,0.189 1.752,0.184 12 for 1VD-FTV: 1.586,1.198 1.998,1.347 0.413,0.149 10 CANH 6.069,0.647 6.461,0.831 0.392,0.184 10 CANL 6.069,1.198 6.482,1.347 0.413,0.149 10 CANH 1.796,1.761 2.049,1.924 0.253,0.163 10 TC 2.09,0.521 2.274,0.698 0.184,0.177 10 49 2.083,1.088 2.288,1.265 0.205,0.177 10 41 2.108,1.663 2.319,1.847 0.211,0.184 10 27 5.8,0.505 6.049,0.679 0.248,0.174 10 22 5.782,1.065 6.058,1.304 0.276,0.239 10 13

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD with Central Gateway ECU) B
DTC is output (for RHD with Central Gateway ECU) C
DTC is output (for LHD without Central Gateway ECU) D
DTC is output (for RHD without Central Gateway ECU) E



A

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

B

C

D

E

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.
U164734E02
1.823,1.865 2,2.125 false 1.969,3.479 2.49,3.521 false 1.958,3.406 2.729,3.26 false 1.771,3.719 2.625,3.854 false 0.063,0.104 1.333,0.302 1.271,0.198 10 false Front view of DLC3: 0.25,1.458 0.573,1.615 0.323,0.156 10 false E22 1.969,2.125 2.24,2.313 0.271,0.188 10 false TC 0.063,2.354 2.448,2.729 2.385,0.375 10 false Front view of wire harness connector: (to ECM) 2.771,3.135 3.115,3.323 0.344,0.188 10 false TC*1 2.552,3.448 2.896,3.635 0.344,0.188 10 false TC*3 0.031,4.073 1.625,4.271 1.594,0.198 10 false *1: for 1GR-FE, 1UR-FE 1.479,4.354 2.26,4.542 0.781,0.188 10 false *4: for LHD 0.031,4.344 1.125,4.531 1.094,0.188 10 false *3: for 1VD-FTV 2.531,4.344 3.302,4.531 0.771,0.188 10 false *5: for RHD 0.219,3.146 0.563,3.323 0.344,0.177 10 false A38 0.635,3.094 0.979,3.271 0.344,0.177 10 false *4 0.635,3.51 0.979,3.688 0.344,0.177 10 false *5 0.208,3.552 0.552,3.729 0.344,0.177 10 false A52 2,4.052 3,4.24 1,0.188 10 false *2: for 3UR-FE 2.708,3.781 3.052,3.969 0.344,0.188 10 false TC*2

Turn the ignition switch off.


b.

Disconnect the connector from the ECM.


c.

for LHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1UR-FE:
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-16 (TC) Always Below 1 Ω

for 3UR-FE:
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-43 (TC) Always Below 1 Ω


for 1VD-FTV:
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-27 (TC) Always Below 1 Ω




d.

for RHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1UR-FE:
Tester Connection Condition Specified Condition
E22-13 (TC) - A52-16 (TC) Always Below 1 Ω

for 3UR-FE:
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-43 (TC) Always Below 1 Ω


for 1VD-FTV:
Tester Connection Condition Specified Condition
E22-13 (TC) - A52-27 (TC) Always Below 1 Ω





OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
U156867E01
0.056,0.045 1.330,0.221 1.274,0.177 10 Front view of DLC3: 0.156,1.185 0.486,1.340 0.330,0.156 10 E22 1.832,1.806 2.162,1.962 0.330,0.156 10 CG 1.606,1.033 1.965,1.761 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-4 (CG) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (TC OF ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC OF ECM - BODY GROUND)
U164736E02
1.958,1.885 2.708,1.76 false 1.979,1.958 2.406,2.052 false 1.771,2.208 2.531,2.344 false 0.125,0.104 2.51,0.448 2.385,0.344 10 false Front view of wire harness connector: (to ECM) 0.24,1.615 0.542,1.802 0.302,0.188 10 false A38 0.677,1.573 0.979,1.76 0.302,0.188 10 false *4 0.677,1.969 0.979,2.156 0.302,0.188 10 false *5 2.771,1.688 3.146,1.854 0.375,0.167 10 false TC*1 2.479,2 2.854,2.167 0.375,0.167 10 false TC*3 0.063,2.563 1.677,2.781 1.615,0.219 10 false *1: for 1GR-FE, 1UR-FE 1.448,2.906 2.25,3.083 0.802,0.177 10 false *4: for LHD 2.49,2.885 3.25,3.073 0.76,0.188 10 false *5: for RHD 0.063,2.917 1.146,3.104 1.083,0.188 10 false *3: for 1VD-FTV 0.229,2.021 0.531,2.208 0.302,0.188 10 false A52 2.094,2.552 3.198,2.75 1.104,0.198 10 false *2: for 3UR-FE 2.594,2.271 2.969,2.438 0.375,0.167 10 false TC*2

a.

for LHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1UR-FE:
Tester Connection Condition Specified Condition
A38-16 (TC) - Body ground Always 1 MΩ or higher

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-43 (TC) - Body ground Always 1 MΩ or higher


for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-27 (TC) - Body ground Always 1 MΩ or higher




b.

for RHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1UR-FE:
Tester Connection Condition Specified Condition
A52-16 (TC) - Body ground Always 1 MΩ or higher

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-43 (TC) - Body ground Always 1 MΩ or higher


for 1GR-FE, 1VD-FTV:
Tester Connection Condition Specified Condition
A52-27 (TC) - Body ground Always 1 MΩ or higher





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU