Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the CAN communication system.

WIRING DIAGRAM

C175154E03
0.06,0.839 1.054,1.051 0.994,0.211 10 from IG Relay 0.166,2.633 1.059,2.844 0.893,0.211 10 from IG Relay 1.778,1.007 2.121,1.177 0.343,0.170 10 IGN 1.76,2.779 2.076,2.942 0.316,0.163 10 MET 1.658,3.37 2.195,3.547 0.537,0.177 10 ECU-B1 0.465,6.315 1.218,6.491 0.753,0.177 10 : CAN Line 2.906,2.565 3.159,2.769 0.253,0.205 10 18 2.913,3.16 3.124,3.330 0.211,0.170 10 17 2.92,4.155 3.124,4.366 0.205,0.211 10 15 3.158,2.663 3.453,2.846 0.295,0.184 10 IG+ 3.158,3.265 3.467,3.463 0.309,0.198 10 B 3.158,4.245 3.453,4.450 0.295,0.205 10 ET 3.654,2.054 4.088,2.196 0.434,0.142 10 CANL 3.647,2.65 4.081,2.813 0.434,0.163 10 CANH 6.151,2.056 6.585,2.198 0.434,0.142 10 CANL 6.151,2.652 6.585,2.815 0.434,0.163 10 CANH 4.131,1.919 4.398,2.088 0.267,0.170 10 26 4.138,2.507 4.364,2.684 0.225,0.177 10 25 5.873,1.928 6.133,2.119 0.260,0.191 10 22 5.873,2.531 6.112,2.714 0.239,0.184 10 13 5.866,3.546 6.078,3.751 0.211,0.205 10 25 5.873,4.138 6.098,4.329 0.225,0.191 10 26 6.151,3.66 6.362,3.816 0.211,0.156 10 E1 6.151,4.263 6.390,4.433 0.239,0.170 10 E2 5.88,0.742 6.059,0.893 0.179,0.151 10 21 6.151,0.849 6.501,1.010 0.350,0.161 10 IG2 3.049,5.599 3.351,5.762 0.302,0.163 10 E7 3.049,5.774 4.358,5.958 1.308,0.184 10 Combination Meter 5.748,5.574 6.085,5.737 0.336,0.163 10 E47 5.748,5.732 7.112,5.937 1.364,0.205 10 Center Airbag Sensor 0.214,3.249 1.046,3.460 0.832,0.211 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Result
Result Proceed to
DTC is not output A
DTCs are output (for LHD) B
DTCs are output (for RHD) C



A

2.CHECK BATTERY

B

C

2.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V




OK

3.CHECK CONNECTORS

NG

3.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and combination meter.

OK:

The connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
a.
U164511E01
0.247,0.288 2.598,0.625 2.350,0.336 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.399,1.63 0.700,1.772 0.302,0.142 10 E47 1.049,3.078 1.289,3.234 0.239,0.156 10 E2 2.295,3.096 2.542,3.238 0.246,0.142 10 E1 2.854,2.339 3.128,2.502 0.274,0.163 10 IG2 1.677,2.485 1.238,3.053 false 1.797,2.468 2.321,3.07 false 2.407,2.425 2.82,2.425 false

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E47-21 (IG2) - E47-25 (E1) Ignition switch ON 11 to 14 V
E47-21 (IG2) - E47-26 (E2) Ignition switch ON 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.
U164731E01
0.071,0.077 2.428,0.420 2.357,0.343 10 Front view of wire harness connector: (to Combination Meter) 0.293,2.053 0.594,2.230 0.302,0.177 10 E7 1.03,2.849 1.157,2.994 0.127,0.145 10 B 0.66,2.855 0.858,3.000 0.198,0.145 10 ET 1.408,2.824 1.689,2.970 0.281,0.145 10 IG+ 1.148,2.463 1.076,2.829 false 0.847,2.46 0.776,2.826 false 1.294,2.475 1.472,2.803 false 1.148,2.463 1.076,2.829 false 0.847,2.46 0.776,2.826 false 1.294,2.475 1.472,2.803 false

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Disconnect the E7 connector from the combination meter.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-17 (B) - E7-15 (ET) Always 11 to 14 V
E7-18 (IG+) - E7-17 (B) Ignition switch ON 11 to 14 V




OK

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.




OK

NG