Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1630/23  Rear Airbag Sensor RH Circuit Malfunction  B1695/16  Door Side Airbag Sensor LH Malfunction  


DESCRIPTION

HINT:

"Door side airbag sensor LH" refer to the side airbag sensor LH.


·

The side airbag sensor LH or rear airbag sensor RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.

If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.

DTC B1630/23 or B1695/16 is stored when a malfunction is detected in the side airbag sensor LH or rear airbag sensor RH circuit.


DTC Code DTC Detection Condition Trouble Area
B1630/23 When one of the following conditions is met:
·

A rear airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

Rear airbag sensor RH

·

Center airbag sensor assembly


B1695/16 When one of the following conditions is met:
·

A side airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Side airbag sensor LH

·

Center airbag sensor assembly



WIRING DIAGRAM

C171802E06
0.091,0.02 1.164,0.280 1.073,0.260 12 for RH Side: 5.696,2.749 6.171,2.889 0.475,0.140 10 BCR- 5.696,1.418 6.171,1.558 0.475,0.140 10 BCR+ 5.433,2.655 5.609,2.830 0.175,0.175 10 2 5.433,1.304 5.609,1.479 0.175,0.175 10 1 1.147,2.749 1.622,2.889 0.475,0.140 10 BCR- 1.147,1.418 1.622,1.558 0.475,0.140 10 BCR+ 3.501,2.757 3.763,2.896 0.262,0.140 10 IL1 3.501,1.422 3.763,1.562 0.262,0.140 10 IL1 1.681,2.655 1.856,2.830 0.175,0.175 10 1 1.681,1.304 1.911,1.479 0.231,0.175 10 2 3.547,2.563 3.722,2.739 0.175,0.175 10 1 3.547,1.213 3.673,1.388 0.126,0.175 10 2 5.308,3.836 5.634,4.000 0.325,0.164 10 I9 5.308,4.015 6.799,4.198 1.491,0.183 10 Side Airbag Sensor RH 0.463,3.836 0.719,4.000 0.256,0.164 10 L18 0.463,4.015 2.393,4.198 1.929,0.183 10 Rear Airbag Sensor RH

C171803E14
1.198,1.469 1.615,1.625 0.417,0.156 10 false BCL+ 1.208,2.802 1.625,2.958 0.417,0.156 10 false BCL- 3.479,1.458 3.771,1.667 0.292,0.208 10 false IK1 3.51,2.792 3.781,2.99 0.271,0.198 10 false IK1 5.688,1.448 6.104,1.604 0.417,0.156 10 false BCL+ 5.688,2.792 6.104,2.948 0.417,0.156 10 false BCL- 1.708,1.344 1.865,1.49 0.156,0.146 10 false 2 1.698,2.688 1.854,2.854 0.156,0.167 10 false 1 3.542,1.24 3.698,1.385 0.156,0.146 10 false 2 3.552,2.583 3.708,2.75 0.156,0.167 10 false 1 5.448,1.344 5.583,1.5 0.135,0.156 10 false 1 5.469,2.667 5.615,2.823 0.146,0.156 10 false 2 0.125,0.083 1.292,0.344 1.167,0.26 12 false for LH Side: 0.365,3.885 0.688,4.073 0.323,0.188 10 false I42 0.354,4.094 2.146,4.333 1.792,0.24 10 false Side Airbag Sensor LH 5.479,3.906 5.917,4.094 0.438,0.188 10 false K7 5.479,4.125 7.042,4.365 1.563,0.24 10 false Rear Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON.


b.

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1630 and B1695 are not output A
DTC B1695 is output B
DTC B1630 is output C



C

2.CHECK REAR AIRBAG SENSOR RH

A

B

3.CHECK SIDE AIRBAG SENSOR LH
2.CHECK REAR AIRBAG SENSOR RH
a.
C171804E03
2.133,1.209 2.910,1.555 0.777,0.347 10 Side Airbag Sensor RH 0.379,1.209 1.205,1.555 0.826,0.347 10 Rear Airbag Sensor RH

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Temporarily replace the rear airbag sensor RH with a new one.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1630 is not output.


HINT:

Codes other than DTC B1630 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK SIDE AIRBAG SENSOR LH
a.
C171804E04
2.133,1.209 2.959,1.555 0.826,0.347 10 Rear Airbag Sensor LH 0.408,1.194 1.173,1.541 0.765,0.347 10 Side Airbag Sensor RH

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the side airbag sensor LH with RH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1690 and B1695 are not output A
DTC B1695 is output B
DTC B1690 is output C

HINT:

Codes other than DTC B1690 and B1695 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


l.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



C

A

B