Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1653/35  Seat Position Airbag Sensor Circuit Malfunction  


DESCRIPTION

The seat position sensor circuit consists of the center airbag sensor and the seat position sensor.

DTC B1653/35 is stored when a malfunction is detected in the seat position sensor circuit.

for LHD
DTC Code DTC Detection Condition Trouble Area
B1653/35 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position sensor circuit for 2 seconds.

·

A seat position sensor malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Seat position sensor

·

Center airbag sensor assembly



for RHD
DTC Code DTC Detection Condition Trouble Area
B1653/35 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position sensor circuit for 2 seconds.

·

A seat position sensor malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Seat position sensor

·

Center airbag sensor assembly



WIRING DIAGRAM

C253111E07
1.25,3.073 2.573,3.417 1.323,0.344 10 false Seat Position Sensor 0.896,4.073 3.25,4.25 2.354,0.177 10 false Front Seat Inner Belt LH 3.094,2.563 3.198,2.729 0.104,0.167 10 false 8 3.073,1.302 3.177,1.469 0.104,0.167 10 false 4 2.667,1.333 3.083,1.531 0.417,0.198 10 false LSP+ 2.688,2.781 3.156,2.99 0.469,0.208 10 false LSP- 5.552,1.417 6.031,1.563 0.479,0.146 10 false LSP+ 5.563,2.677 6.031,2.823 0.469,0.146 10 false LSP- 5.198,3.792 5.604,3.979 0.406,0.188 10 false K27 5.302,2.604 5.5,2.771 0.198,0.167 10 false 17 5.313,1.344 5.51,1.51 0.198,0.167 10 false 9 5.177,3.969 6.958,4.198 1.781,0.229 10 false Center Airbag Sensor 0.896,3.875 1.354,4.073 0.458,0.198 10 false K10 0.156,0.094 2.156,0.344 2,0.25 12 false w/ Side Airbag (for LHD):

C174604E05
0.371,4.106 0.722,4.262 0.350,0.156 10 K10 0.371,4.274 1.937,4.416 1.566,0.142 10 Front Seat Inner Belt LH 0.595,3.423 2.362,3.586 1.767,0.163 10 Seat Position Sensor 2.94,2.916 3.075,3.093 0.135,0.177 10 8 2.538,2.891 2.909,3.061 0.371,0.170 10 LSP- 2.508,1.399 2.879,1.568 0.371,0.170 10 LSP+ 5.699,3.014 6.070,3.184 0.371,0.170 10 LSP- 5.444,2.924 5.675,3.103 0.231,0.180 10 13 5.699,1.511 6.070,1.681 0.371,0.170 10 LSP+ 2.942,1.431 3.084,1.594 0.142,0.163 10 4 5.444,1.42 5.675,1.600 0.231,0.180 10 14 5.443,4.093 5.780,4.256 0.336,0.163 10 K32 5.443,4.267 6.814,4.430 1.371,0.163 10 Center Airbag Sensor 0.149,0.087 2.479,0.308 2.330,0.221 12 w/o Side Airbag (for LHD):

C253111E08
1.271,3.052 2.635,3.281 1.365,0.229 10 false Seat Position Sensor 0.771,4.042 2.521,4.26 1.75,0.219 10 false Front Seat Inner Belt LH 3.094,2.563 3.25,2.76 0.156,0.198 10 false 8 3.094,1.302 3.198,1.469 0.104,0.167 10 false 4 2.635,1.323 3.063,1.49 0.427,0.167 10 false RSP+ 2.656,2.573 3.135,2.76 0.479,0.188 10 false RSP- 5.552,1.417 6.031,1.615 0.479,0.198 10 false RSP+ 5.552,2.677 6.021,2.865 0.469,0.188 10 false RSP- 5.385,3.865 5.646,4.031 0.26,0.167 10 false L27 5.281,2.573 5.479,2.781 0.198,0.208 10 false 24 5.281,1.313 5.479,1.479 0.198,0.167 10 false 16 5.375,4.021 6.729,4.25 1.354,0.229 10 false Center Airbag Sensor 0.771,3.865 1.073,4.042 0.302,0.177 10 false L33 0.115,0.104 2.063,0.396 1.948,0.292 12 false w/ Side Airbag (for RHD):

C174604E06
0.371,4.106 0.722,4.262 0.350,0.156 10 L33 0.371,4.274 1.937,4.416 1.566,0.142 10 Front Seat Inner Belt RH 0.595,3.423 2.362,3.586 1.767,0.163 10 Seat Position Sensor 2.94,2.916 3.075,3.093 0.135,0.177 10 8 2.483,2.891 2.855,3.061 0.371,0.170 10 RSP- 2.483,1.399 2.879,1.568 0.395,0.170 10 RSP+ 5.699,3.014 6.070,3.184 0.371,0.170 10 RSP- 5.444,2.924 5.675,3.103 0.231,0.180 10 13 5.699,1.511 6.123,1.681 0.424,0.170 10 RSP+ 2.942,1.431 3.084,1.594 0.142,0.163 10 4 5.444,1.42 5.675,1.600 0.231,0.180 10 12 5.443,4.093 5.733,4.256 0.290,0.163 10 L38 5.443,4.267 6.814,4.430 1.371,0.163 10 Center Airbag Sensor 0.149,0.087 2.479,0.308 2.330,0.221 12 w/o Side Airbag (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check vehicle condition.

Result
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR DTC

B

9.CHECK FOR DTC
2.CHECK FOR DTC
a.
C174605E03
0.048,0.003 1.750,0.279 1.702,0.276 12 w/ Side Airbag: 0.048,2.367 1.750,2.643 1.702,0.276 12 w/o Side Airbag: 1.892,3.834 2.784,4.161 0.892,0.327 10 Center Airbag Sensor 0.524,3.741 1.481,4.054 0.957,0.313 10 Seat Position Sensor 1.892,1.764 2.784,2.091 0.892,0.327 10 Center Airbag Sensor 0.451,1.403 1.408,1.716 0.957,0.313 10 Seat Position Sensor

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK CONNECTION OF CONNECTORS
3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the seat position sensor.

OK:

The connectors are properly connected.




OK

4.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the seat position sensor.


b.

Check that the connectors (on the center airbag sensor side and seat position sensor side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

5.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U165399E01
0.267,3.396 1.160,3.543 0.893,0.147 10 Floor Wire 0.533,4.074 0.671,4.258 0.139,0.184 10 D 0.833,4.269 1.045,4.471 0.211,0.202 10 C 1.16,4.269 1.390,4.480 0.230,0.211 10 B 1.478,4.069 1.718,4.272 0.239,0.202 10 A 1.318,4.575 2.234,4.879 0.915,0.304 10 Center Airbag Sensor 0.083,4.499 1.019,4.821 0.936,0.322 10 Seat Position Sensor 4.796,3.196 7.142,3.557 2.347,0.361 10 Rear view of wire harness connector: (to Center Airbag Sensor) 2.689,4.157 2.965,4.350 0.276,0.193 10 K10 4.9,4.185 5.183,4.350 0.283,0.165 10 K32 4.903,5.008 5.327,5.183 0.424,0.174 10 LSP+ 5.597,4.683 5.099,5.005 false 3.886,4.55 4.760,4.692 0.873,0.142 10 Connector C 6.268,4.566 7.077,4.722 0.809,0.156 10 Connector B 0.961,3.477 1.091,3.477 1.091,3.477 1.051,4.092 false 0.257,0.598 1.150,0.745 0.893,0.147 10 Floor Wire 0.523,1.276 0.661,1.460 0.139,0.184 10 D 0.824,1.471 1.035,1.673 0.211,0.202 10 C 1.15,1.471 1.380,1.683 0.230,0.211 10 B 1.469,1.258 1.708,1.460 0.239,0.202 10 A 1.309,2.015 2.224,2.319 0.915,0.304 10 Center Airbag Sensor 0.073,1.701 1.009,2.024 0.936,0.323 10 Seat Position Sensor 2.236,0.636 4.653,0.997 2.416,0.361 10 Front view of wire harness connector: (to Seat Position Sensor) 2.236,3.196 4.653,3.557 2.416,0.361 10 Front view of wire harness connector: (to Seat Position Sensor) 4.786,0.636 7.133,0.997 2.347,0.361 10 Rear view of wire harness connector: (to Center Airbag Sensor) 2.679,1.598 2.955,1.791 0.276,0.193 10 K10 4.899,1.625 5.197,1.791 0.297,0.165 10 K27 3.889,4.171 4.313,4.327 0.424,0.156 10 LSP+ 3.889,4.913 4.249,5.087 0.360,0.174 10 LSP- 3.537,4.667 3.873,4.961 false 3.537,4.562 3.873,4.268 false 3.889,1.61 4.313,1.765 0.424,0.156 10 LSP+ 3.889,2.351 4.249,2.526 0.360,0.174 10 LSP- 6.413,1.627 6.838,1.802 0.424,0.174 10 LSP+ 5.929,2.712 6.353,2.886 0.424,0.174 10 LSP- 6.404,1.677 6.037,1.974 false 6.509,2.363 6.313,2.097 false 6.039,2.668 6.026,2.118 false 3.876,1.991 4.750,2.133 0.873,0.142 10 Connector C 5.368,1.292 6.177,1.448 0.809,0.156 10 Connector B 0.951,0.678 1.081,0.678 1.081,0.678 1.042,1.294 false 0.112,2.698 1.472,2.937 1.360,0.239 12 w/o Side Airbag: 0.112,0.043 1.287,0.283 1.174,0.239 12 w/ Side Airbag: 3.537,2.105 3.873,2.4 false 3.537,2 3.873,1.706 false 6.262,4.997 6.622,5.171 0.360,0.174 10 LSP- 5.722,4.695 6.246,5.045 false 5.341,5.188 6.149,5.343 0.809,0.156 10 Service wire 5.587,5.009 5.587,5.166 false 6.292,2.384 7.101,2.540 0.809,0.156 10 Service wire


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K10-4 (LSP+) - Body ground Ignition switch ON Below 1 V
K10-8 (LSP-) - Body ground Ignition switch ON Below 1 V



d.

w/ Side Airbag:

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Using a service wire, connect terminals 9 (LSP+) and 17 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-4 (LSP+) - K10-8 (LSP-) Always Below 1 Ω



v.

Disconnect the service wire from connector B.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-4 (LSP+) - K10-8 (LSP-) Always 1 MΩ or higher
K10-4 (LSP+) - Body ground Always 1 MΩ or higher
K10-8 (LSP-) - Body ground Always 1 MΩ or higher




e.

w/o Side Airbag:

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Using a service wire, connect terminals 14 (LSP+) and 13 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-4 (LSP+) - K10-8 (LSP-) Always Below 1 Ω



v.

Disconnect the service wire from connector B.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-4 (LSP+) - K10-8 (LSP-) Always 1 MΩ or higher
K10-4 (LSP+) - Body ground Always 1 MΩ or higher
K10-8 (LSP-) - Body ground Always 1 MΩ or higher





OK

6.CHECK SEAT POSITION SENSOR (FRONT SEAT INNER BELT LH)

NG

REPLACE FLOOR WIRE

6.CHECK SEAT POSITION SENSOR (FRONT SEAT INNER BELT LH)
a.
C174605E03
0.048,0.003 1.750,0.279 1.702,0.276 12 w/ Side Airbag: 0.048,2.367 1.750,2.643 1.702,0.276 12 w/o Side Airbag: 1.892,3.834 2.784,4.161 0.892,0.327 10 Center Airbag Sensor 0.524,3.741 1.481,4.054 0.957,0.313 10 Seat Position Sensor 1.892,1.764 2.784,2.091 0.892,0.327 10 Center Airbag Sensor 0.451,1.403 1.408,1.716 0.957,0.313 10 Seat Position Sensor

Connect the connectors to the center airbag sensor and the seat position sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.




OK

NG

7.REPLACE SEAT POSITION SENSOR (FRONT SEAT INNER BELT LH)
7.REPLACE SEAT POSITION SENSOR (FRONT SEAT INNER BELT LH)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt LH (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

8.CHECK CENTER AIRBAG SENSOR
8.CHECK CENTER AIRBAG SENSOR
a.
C174605E03
0.048,0.003 1.750,0.279 1.702,0.276 12 w/ Side Airbag: 0.048,2.367 1.750,2.643 1.702,0.276 12 w/o Side Airbag: 1.892,3.834 2.784,4.161 0.892,0.327 10 Center Airbag Sensor 0.524,3.741 1.481,4.054 0.957,0.313 10 Seat Position Sensor 1.892,1.764 2.784,2.091 0.892,0.327 10 Center Airbag Sensor 0.451,1.403 1.408,1.716 0.957,0.313 10 Seat Position Sensor

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

9.CHECK FOR DTC
a.
C146230E15
0.464,1.452 1.403,1.766 0.939,0.314 10 Seat Position Sensor 1.614,1.193 2.987,1.369 1.374,0.176 10 Center Airbag Sensor

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.




OK

NG

10.CHECK CONNECTION OF CONNECTORS
10.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the seat position sensor.

OK:

The connectors are properly connected.




OK

11.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

11.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the seat position sensor.


b.

Check that the connectors (on the center airbag sensor side and seat position sensor side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

12.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)

NG

REPLACE NO. 2 FLOOR WIRE

12.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U165400E02
5.01,5.083 5.656,5.021 false 4.615,2 4.104,2.417 false 4.677,2.135 4.969,2.479 false 1.052,4.594 1.552,4.823 false 1.177,5.365 1.531,4.99 false 1.271,0.802 1.396,0.802 1.396,0.802 1.354,1.417 false 4.875,5.083 4.385,5.354 false 5.125,5.385 5.323,5.385 false 0.969,4.938 1.167,4.938 false 3.969,3.563 6.313,3.927 2.344,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.094,4.552 4.385,4.719 0.292,0.167 10 false L38 5.719,4.938 6.146,5.115 0.427,0.177 10 false RSP+ 5.313,4.417 6.125,4.573 0.813,0.156 10 false Connector B 0.208,0.677 1.281,0.823 1.073,0.146 10 false No. 2 Floor Wire 0.844,1.365 0.979,1.552 0.135,0.188 10 false D 1.146,1.583 1.354,1.781 0.208,0.198 10 false C 1.469,1.583 1.698,1.792 0.229,0.208 10 false B 1.802,0.896 2.042,1.094 0.24,0.198 10 false A 1.635,1.677 2.552,2.063 0.917,0.385 10 false Center Airbag Sensor 0.292,1.833 1.177,2.177 0.885,0.344 10 false Seat Position Sensor 3.344,0.615 5.76,0.979 2.417,0.365 10 false Front view of wire harness connector: (to Seat Position Sensor) 0.906,3.563 3.25,3.927 2.344,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 3.802,1.583 4.073,1.781 0.271,0.198 10 false L33 1.083,4.344 1.406,4.51 0.323,0.167 10 false L27 3.719,2.385 4.146,2.542 0.427,0.156 10 false RSP+ 4.99,2.385 5.354,2.563 0.365,0.177 10 false RSP- 0.646,4.51 1.073,4.688 0.427,0.177 10 false RSP+ 0.771,5.313 1.198,5.49 0.427,0.177 10 false RSP- 4.99,1.969 5.865,2.115 0.875,0.146 10 false Connector C 2.385,4.479 3.198,4.635 0.813,0.156 10 false Connector B 3.896,3.063 5.25,3.302 1.354,0.24 12 false w/o Side Airbag: 0.844,3.094 2.021,3.333 1.177,0.24 12 false w/ Side Airbag: 4.042,5.313 4.406,5.49 0.365,0.177 10 false RSP- 5.396,5.302 6.208,5.458 0.813,0.156 10 false Service Wire 0.146,4.865 0.958,5.021 0.813,0.156 10 false Service Wire


b.

Turn the ignition switch to ON.


c.

Measure the voltage according the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L33-4 (RSP+) - Body ground Ignition switch ON Below 1 V
L33-8 (RSP-) - Body ground Ignition switch ON Below 1 V



d.

w/ Side Airbag:

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Using a service wire, connect terminals 16 (RSP+) and 24 (RSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L33-4 (RSP+) - L33-8 (RSP-) Always Below 1 Ω



v.

Disconnect the service wire from connector B.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L33-4 (RSP+) - L33-8 (RSP-) Always 1 MΩ or higher
L33-4 (RSP+) - Body ground Always 1 MΩ or higher
L33-8 (RSP-) - Body ground Always 1 MΩ or higher




e.

w/o Side Airbag:

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Using a service wire, connect terminals 12 (RSP+) and 13 (RSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L33-4 (RSP+) - L33-8 (RSP-) Always Below 1 Ω



v.

Disconnect the service wire from connector B.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L33-4 (RSP+) - L33-8 (RSP-) Always 1 MΩ or higher
L33-4 (RSP+) - Body ground Always 1 MΩ or higher
L33-8 (RSP-) - Body ground Always 1 MΩ or higher





OK

13.CHECK SEAT POSITION SENSOR (FRONT SEAT INNER BELT RH)

NG

REPLACE NO. 2 FLOOR WIRE

13.CHECK SEAT POSITION SENSOR (FRONT SEAT INNER BELT RH)
a.
C146230E15
0.464,1.452 1.403,1.766 0.939,0.314 10 Seat Position Sensor 1.614,1.193 2.987,1.369 1.374,0.176 10 Center Airbag Sensor

Connect the connectors to the center airbag sensor and the seat position sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.




OK

NG

14.REPLACE SEAT POSITION SENSOR
14.REPLACE SEAT POSITION SENSOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the seat position sensor (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL).

HINT:

Perform inspection using parts from a normal vehicle if possible.




NEXT

15.CHECK CENTER AIRBAG SENSOR
15.CHECK CENTER AIRBAG SENSOR
a.
C146230E15
0.464,1.452 1.403,1.766 0.939,0.314 10 Seat Position Sensor 1.614,1.193 2.987,1.369 1.374,0.176 10 Center Airbag Sensor

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG