The seat position sensor circuit consists of the center airbag sensor and the seat position sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position sensor circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1653/35 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position sensor circuit for 2 seconds. ·
A seat position sensor malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Seat position sensor ·
Center airbag sensor assembly |
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1653/35 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position sensor circuit for 2 seconds. ·
A seat position sensor malfunction. ·
A center airbag sensor malfunction. |
·
No. 2 floor wire ·
Seat position sensor ·
Center airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1653 is not output.
Codes other than DTC B1653 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the seat position sensor.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and the seat position sensor.
Check that the connectors (on the center airbag sensor side and seat position sensor side) are not damaged.
The connectors are not deformed or damaged.
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K10-4 (LSP+) - Body ground | Ignition switch ON | Below 1 V |
| K10-8 (LSP-) - Body ground | Ignition switch ON | Below 1 V |
w/ Side Airbag:
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 9 (LSP+) and 17 (LSP-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-4 (LSP+) - K10-8 (LSP-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-4 (LSP+) - K10-8 (LSP-) | Always | 1 MΩ or higher |
| K10-4 (LSP+) - Body ground | Always | 1 MΩ or higher |
| K10-8 (LSP-) - Body ground | Always | 1 MΩ or higher |
w/o Side Airbag:
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 14 (LSP+) and 13 (LSP-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-4 (LSP+) - K10-8 (LSP-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-4 (LSP+) - K10-8 (LSP-) | Always | 1 MΩ or higher |
| K10-4 (LSP+) - Body ground | Always | 1 MΩ or higher |
| K10-8 (LSP-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connectors to the center airbag sensor and the seat position sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1653 is not output.
Codes other than DTC B1653 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the front seat inner belt LH (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL).
Perform the inspection using parts from a normally functioning vehicle if possible.
NEXT
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1653 is not output.
Codes other than DTC B1653 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1653/35 is not output.
Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the seat position sensor.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and the seat position sensor.
Check that the connectors (on the center airbag sensor side and seat position sensor side) are not damaged.
The connectors are not deformed or damaged.
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L33-4 (RSP+) - Body ground | Ignition switch ON | Below 1 V |
| L33-8 (RSP-) - Body ground | Ignition switch ON | Below 1 V |
w/ Side Airbag:
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 16 (RSP+) and 24 (RSP-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L33-4 (RSP+) - L33-8 (RSP-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L33-4 (RSP+) - L33-8 (RSP-) | Always | 1 MΩ or higher |
| L33-4 (RSP+) - Body ground | Always | 1 MΩ or higher |
| L33-8 (RSP-) - Body ground | Always | 1 MΩ or higher |
w/o Side Airbag:
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 12 (RSP+) and 13 (RSP-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L33-4 (RSP+) - L33-8 (RSP-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L33-4 (RSP+) - L33-8 (RSP-) | Always | 1 MΩ or higher |
| L33-4 (RSP+) - Body ground | Always | 1 MΩ or higher |
| L33-8 (RSP-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connectors to the center airbag sensor and the seat position sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1653/35 is not output.
Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the seat position sensor (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL).
Perform inspection using parts from a normal vehicle if possible.
NEXT
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1653/35 is not output.
Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.
OK
NG